36358092892 Kenmore Refrigerator - Instructions

Remove lower front panel, disconnect damaged union from water hose under freezer door, replace with new union, tighten and reattach front panel. No more water coming from under the unit. Ice maker and dispenser features returned to working order!

I began by turning off the refridgerator and then removing all of the drawers/bins and icemaker from the freezer.

I removed the three phillips-head screws across the top of the rear access panel. (same height as the light bulb) I then removed the two phillips-head screws from the bottom of the access panel.

I removed the access panel by swinging the left side forward to clear the drawer slides, while keeping the right side back against itsattaching points. (Like a door swinging on its hinges.)

I followed the wire harness from the upper heating element up to its connector and unplugged the defrosting heaters from the plug. I then gently removed the little (just smaller than a tea light candle) thermostat from the top of the coils. (Not far from where the wire connector was.)

I removed two phillips head screws for each heater unit and removed the whole thing as on big assembly.

I installed the new parts from the bottom up, careful not to damage anything. I installed the new thermostat carefully and then reconnected the wire harness. Next I reinstalled the access panel, starting twith the top center screw to hold it in place during the installation of the other 4 screws in the corners.

Lastly, I put the drawers / bins and icemaker back in and turned the refrigerator back on. DONE.

It corrected the problem. THANKS for the Great Customer Service, too!

Turned off power, removed cover from Ice maker, checked resistance across thermostat for zero (read open), all other switches read proper value (when activated). Ordered and received thermostat. Removed Ice Maker from freezer, removed two screws holding ice tray to Control Assembly. Removed Thermostat and replaced with new one. Applied Silicone Sealant to face of Thermostat for adhesion to ice tray when assembled. Remounted Ice Tray to Control Assembly and remounted in freezer. Works Great...

This Valve Has 2 Different Size Water Lines Going In To It And They Are Different Diameters.Each Has Its Own Collar That Locks The Lines Into It. Make Sure That You Put The Right Size Collar Over The Line Before You Insert It Into The Valve, Because Once You Put The Line In You Cant Pull It Back Out Without Messing Up The Valve. Make Sure It Is Right Because You Only Get One Shot At It.

Take the back panel off inside of freezer side. Cut the wires off old Defrost Thermostat and strip the ends. Attach the wires of the new one and tighten with wire nuts. Put back panel back on.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

First I turned the refrigerator and water line off. Then moved to the freezer section, followed the directions, removed the two screws. Directions state to not remove them but I had to in this case. Unplugged the ice maker and removed it from the freezer. I installed the two mounting screws then tried to plug the electrical connection back in but had to use the adaptor cord furnished in the kit. The cord was a little long but I tucked it in and mounted the ice maker. Turned it on then turned the refrigerator and water back on and in a few hours had ice! Very easy to do!

It took me about 15 minutes to complete the repair, 1st I emptied the ice maker, then I removed 4 screws from the rear of the ice maker tray and took the plastic piece off of the auger. I reversed the steps and put it back together.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

remove lower back cover - disconnect wires to fan motor - place 6" fan to blow on condenser - fridge began cooling & freezing again - ordered part - part arrived - removed fan motor & bracket - cleaned brackets & fan blade - cleaned lint & dust from condenser compartment (took longer to clean than anything else) - replaced fan motor - replaced cover - was hero with wife ... :-)

What can I tell you to help except if the 75+ year old Grandma can do it you can do it also. This site was great and the shipping was super fast.

Have put up with an ice maker that never automatically quit making ice for over a year. I just manually shut it off (remembered some of the time and was reminded by the error messages when overflowing at other times). I just didn't want to pay for a service call and all that involves for this item. Then the incoming waterline split and I had to make a decision and that was to DIY the repair after reading the info on this site. The ice maker was a breeze and you can read the details in other posts. Here I will say it takes removing two screws to loosen (mine wouldn't slip off unless screws were totally removed), (I shut off the water and unplugged refrigerator since I am neither an electrician nor an appliance repairman) unplugging the ice maker by removing one hex head, removing the control cover (bottom to top as described in other posts), remove 3 screws only in the metal plate that holds the inside of the ice maker together to get access to the "brains", replaced the Cam, reverse to reassemble (remembering to get the arm back into it's hole in the metal plate. End of that job.

After reading posts about the the water line tubing, I made sure that I had all of the parts of the correct size to replace all of the tubing that passes by the compressor. I did not, however, replace the full length of any of the tubing. I cut off the bad sections of the 1/4" to the middle of the back of the refrigerator and connected a new section with the 1/4" x 1/4" water tube unions.(I was able to buy 1/4" water line, 5/16" water line and 1/4" x 1/4" water tube unions locally but I could not find 5/16" x 5/16" water tube unions so I ordered them from PartSelect at the same time as I ordered the ice maker cam.)

Then I went to the inside of the refrigerator removed the cover from the water reservoir (behind the hydrator), cut out the old section of the water dispenser lines that pass by the compressor, threaded in (not as easy as the outside tubes but not difficult either) the new tubing and connected with the 5/16" x 5/16" water tube unions. You will get lots more details in other posts but this is to tell you that you CAN DO IT with help from this site! I fixed it all for less than $20 (versus cost of new refrigerator, or new ice maker, or service call).

removed 3 screws unplug and remove old unit. install two screws install new ice maker, tighten screws plug in and turn on. had ice in 20 min.

Simple. UNPLUG THE FRIDGE. Remove set screw holding valve to frame, switch hoses one at a time into new valve, switch wires one set at a time from old to new, re-attach the new valve, turn on water , plug in fridge, check for leaks. 2-minute job.

Pulled out the fridge, took off the cardboard back. Get a nut driver instead of screwdriver (easier). TURN OFF WATER NOW. UNPLUG FRIDGE NOW. Removed one screw holding valve. Pulled off electrical connectors. Use two small adjustable wrenches to remove water lines. Tag the plastic tubes (I marked RED and BLUE). Grab the new valve and try to stuff it into the same space. Whoops ! Dang plastic housing protecting the electrical from the water is in the way. Have to cut most of it out to make it fit. By the way, DONT follow the instructions about take the bracket off the OLD solenoid. You don't need it. Just throw it away. Connect the wires (remember to use the adapters sent with the new solenoid) Mount the new solenoid (now that the plastic is out of the way) with the one screw (nut driver). Hook up the supply water line (wrenches). Hook up the plastic tubes (aren't you glad you marked them ?). The tubes just push into the new solenoid, no more threads. I just left the plastic nuts on the tubing. TURN ON THE WATER. Check your connections for leaking. Do this before plugging in the fridge. If OK, plug in the fridge. Run some water on the door, look in about an hour to see if cubes are making now. Put cardboard back on fridge. Push fridge back against wall. CONGRATULATE YOURSELF ON A JOB WELL DONE.

Bing , Bang, Boom.