10667181790 Kenmore Refrigerator - Instructions

My troubleshooting narrowed down the problem to either the control assembly or the thermostat, so I bought both just in case. The motor assembly fixed the problem and I didn't need to install the thermostat.

The main thing I want to tell others who are doing this repair, however, relates to the thermostat. If you do indeed need to replace the thermostat (#PS380941) there is something you will need that is not included with the part or mentioned anywhere on this site. The instructions with the thermostat indicate you need to apply something called "Aluminastic" to the thermostat when installing it. I don't know about you, but that isn't something I have around the house, so be sure to order a tube of it when you get the thermostat so you don't have to take a trip to the store to get it to finish the repair.

first I diagnosed the problem with the whirlpool do-it-yourself repair manual, which was very easy to understand. as per the repair manual, "this part located on the evaporator or the back of the liner is used during the defrost cycle. This bimetal senses the temperature from the evaporator. When the temperature reaches 50-70 degrees (F) the defrost bimetal turnd the defrost heater off. " then I emptied the freezer. removed the the back panel to expose the evaporator. I looked for the bimetal defrost thermostat clipped on the evaporator. tested the bi-metal defrost thermostat, as per the manual, " the ohmmeter should show ZERO resistance (continuity). if not, the bimetal is bad and needs replacing." NOTE: the bimetal must be cold. it is also tested with the bimetal warm/hot, by running it under hot water. i used a styrofoam cup with hot water & dipped the bimetal in. as per the manual, " the ohmmeter should show an open circuit. if not, the bimetal is bad and needs replacing. then got online found partselect.com. ordered the part, recieved it in less than 2 days. within minutes after recieving the part, I removed the bimetal defrost thermostat and spliced in the new one. thanks to partselect.com my fridge is back up and running properly again. prior to installing the new bimetal, i tested it, as descibed above, you can hear & feel the bimetal open/close when it gets hot/cold.

De-iced the refrigerator. Removed two screws from the thermostat panel on the upper refrigerator section. Tilted it down, removed two speed nuts holding the timer, unplugged the timer plug. Determined from the instruction sheet (easy to follow) what time delay function is used, based on wire colors, placed the jumper on the correct terminal on the new timer. Plugged it in, replaced the speed nuts and screws. The timer fit perfect, works just like it is supposed to, quick easy job.

First I removed the old lightbulb from the socket and replaced it with a new one to confirm that the bulb was not the problem. I then pryed the socket out with a flat-head screwdriver. I could tell that the socket was anchored in its hole with clips so it was relatively easy to pry it out. Once the socket was out, I disconnected the lead wires and ordered a replacement socket kit from Partselect. When the new one arrived, I reconnected the lead wires to it, snapped it back into its hole, screwed in a new lightbulb, and presto!! The light was back on with no further problem. Thank you, Partselect!! A $15.00 part saved me what probably would have been at least a $100. service call and heaven knows what the technician would have told me I needed!!!

I first poured water into the ice maker itself and it made ice, so knew the ice maker itself was working ok. Turned the water valve at the wall off, removed the inlet valve from the back of the fridge with a nut driver, disconnected the solenoid wires and disconnected the water supply line entering the inlet valve and turned the water supply back on and found that the water was flowing ok out of the supply line. Reconnected the water line to the inlet valve and disconnected the water line going from the inlet valve to the ice maker and reconnected the wires to the solenoid on the inlet valve and found no water going through and so determined that the inlet valve/solenoid was faulty and easily replaced it. Note that an ohmeter check said the solenoid was ok, so it could have been that the filter screen inside the inlet valve was blocked. It's a sealed unit, so there was no way to take the screen out to check.

First disconnected the quick release electrical connection. Then loosened the three screws that were holding the motor in the bracket. However, space is limited and even with small hands it was rather difficult as the screws were in there very tight. There are a few sharp edges on the bracket and in the surrounding area of the motor area, and nicked myself a couple of times. Removed the fan blade from the old motor and attached it the new motor with the old flat washer/screw. Reconnected the electrical connection and that was that. All-in-all an easy repair.

I removed the ice maker which required removing 3 screws and then disconnecting the electrical plug. Once the ice maker was out, I removed the 3 screws that held the motor assembly to the unit.
I removed the motor, replacing it with the new one.
Plugged the power supply cord back in, replaced the unit with the 3 screws and within a few minutes the unit was receiving water and by the next day I had ICE. This saved me $50. for the service call, then another $25.00 installation fee when the part came in (had to be ordered) plus the markup on the motor (approx. $25.00) So I saved approx. $100. and only took about 30 min.

Originally replaced water inlet valve, not the problem. Tried to work from cheap to expensive.
1. Turn off power, shut off water supply
2. Loosen top two screws of ice maker (will slide up and off, no need to take top two out)
3.Remove bottom screw from ice maker
4.Pulled unit, snapped out existing wire harness
5.Cut hole for water inlet on end of new unit and attached wire icemaking on/off bracket.
6 Connected existing wiring harness to new unit
7. Slid new unit down onto top two screws, put in bottom screw and tightened all three
8. Turned on power and water supply
Had ice being made within two hours. Part Select has given me great service, highly recommend.

1. turn off power.
2. pop off ice maker cover to access motor assembly.
3. remove three screws to assembly.
4. pull off assembly.
5. attach new assembly making sure metal arm and plastic
ice tray rod align with assembly.
6. screw assembly onto unit.
7. replace cover.
8. plug in refrigerator.
9. enjoy ice again with no leakage into freezer.

I removed two screws on the top and one underneath the unit. Then I disconnected the cable. The hardest part was getting the nut driver on the bottom screw because it was obscured by the unit. The replacement unit plugged right in! I got my first batch of ice in about 20 minutes. All I really needed was the timer unit, but the entire ice maker wasn't much more expensive, especially when you consider the time saved on installation!

The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting power in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.

Received my kit quickly. Job was fast and easy. Removed 3 screws with nutdriver and unpluged the wiring harness. Use a flat blade screwdriver to lift the tab on the plastic end cap of the harness. The icemaker comes out in one piece. The wiring harness that came installed on the replacement icemaker matched mine perfectly. (It comes with two others). I plugged the new one in, replaced the screws, bottom one first to help hold it while replacing the top two screws. I used the shut-off arm from my faulty icemaker. Turned the power back on and put 1/2 cup of water in the tray and walked away. Ice dropping into the bin was music to my ears. Didn't need any of the clips or things that came with the icemaker. It was basically a "plug and play". I'm so happy to have ice again, and at a great savings!

I had a technician called out to the house to look at repairing several appliances that all have broken parts after just 3 yrs of use. Hood, Microwave, Oven, Fridge all in need of minor repairs..

Anyway - the estimate was $240 to replace the ice maker. I ordered PS358591 for $104. and it came in a couple days.. I took out one screw - slid out the icemaker, unplugged it - plugged in new one and slid it in the slot - and done !! Took about 20 mins.. didnt need any of the wiring harnesses in the box from partselect. Was way to easy to do !!

Thank you !

First, I unplugged the power to the entire fridge, and then removed the ice tray and ice door. Next, I unplugged the flat plug in the very back left behind the icemaker. Then I removed the 1/4" hex head sheet metal screws (2) and the phillips head screw (1) that hold the icemaker to the left side of the freezer wall. New icemaker came with a different style trip arm, so I used it. Plugged new icemaker in before reattaching it with the same (3) screws. Replaced ice tray and door, plugged in fridge, and waited....Dumped its first batch of ice maybe a couple of hours later. Not much trouble-shooting is needed when the entire icemaker is as easy and relatively inexpensive to replace as this. Twenty minutes, max.

We weren't sure if the problem was in the Water Inlet Valve or in the Icemaker Control & Motor Assembly. The water in the door did work. We removed the Water Inlet Valve & tested it with an Ohm Meter. It tested good so we put it back in. We then ordered the Icemaker Control & Motor Assembly. When it arrived we installed it and waited a few hours but the icemaker still did not fill with water. We telephoned a parts store and were told the problem could be the thermostat or we could replace the whole icemaker. We replaced the whole icemaker.