36378282893 Kenmore Refrigerator - Instructions

First I removed the electrical plug from the back of the freezer that plugs into the icemaker. I then removed the two hex head screws that hold the icemaker to the wall of the freezer and removed the icemaker. I removed the plastic cover, which incidentally protects the gears, by prying it off with a srewdriver. I removed three small nuts(7mm) which holds the internal cam in place. I removed the cam by pulling it off the shaft. Once I got the part from you folks I reversed the procedure that I just mentioned, and put the icemaker back together. It works great. The part with shipping was around $16.00. A new icemaker was roughly $159.00. If I would have called a technician it would have cost around $300.00 to repair.

I had made a dry run at the repair after watching the instructional film provided by part select and it seemed easy enough.
The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws.
Cranking out ice like crazy.

Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.

removed back cover--disconnect water supply-- removed screw holding vave and unplugged the
electric from the valve-- disconncect waterline to
the icemaker. reverse the to put on new part.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Took out both draws and glass shelf, removed the entire lower shelf housing. I snapped off the front rail aluminum face to expose the screw. Unscrewed both screws and removed the rail and then just reversed the procedure to put new rail on. It was the most cost effective way of doing it. All the pieces are there on the GE website as long as you know the model number. You will save a lot of money by doing it yourself.

I had to remove the glass shelve, the two drawers, and the middle rail. Once I did that, I slide the unit out together. I placed the unit on the floor and removed the one screw located on the far backside of the unit. I had to remove a slip cover (it had the kenmore logo and the writting on it) it was a snap on, so no problem. Glad it was not gluded on. After the old part was removed, I put the new part on. Put the two screws back on and snap the cover back on. Then I put the whole unit back in. This included the glassshelve and drawers. The process was pretty easy. Good luck with your change.

I pulled out the shelf and removed the 2 screws holding the broken side rail to the shelf frame. I then screwed the new rail in and set the shelf back in.

Unscrewed four screws, two on each part, and replaced broken parts, reinserting screws. This is a no-brainer repair.

Basically I removed 4 screws holding the rails together, did a little cleaning of the existing parts that I would re-use and screwed the 4 screws back in and put it back into the fridge. Piece of cake. If I hadn't cleaned up the old parts it would have taken me 5 minutes.

removed produce drawers, removed center piece front cover, removed glass shelf, removed broken drawer slide rail - unscrewing where attached in the rear of the refrigerator. Also removed screw from centerpiece where broken drawer slide rail was attached. reassembled all very quickly....saved myself having to buy another refrigerator by doing this simple repair.

Had to defrost the freezer to melt off all the ice before servicing. Once that was done the icemaker replacement only took about 15-30 minutes to complete. The new icemaker came with many accessories and adaptors that were not needed and the instructions were based on replacing an older model and not really clear for my model. They mentioned not being able to use the new stripper but it was exactly the same as the old one so I left the new one in place. All in all it was easy and did the job.

I watched videos of the modern refrigerators and figured out how to do my model by taking my time watching as many videos that pertain to my refrigerator I finally I expose the evaporator I noticed that the defrost heater was buckled up and totally disintegrated and slowly took my time looking at the screws I took it out and I didn't have to do
disassemble bottom of the freezer to replace the part, you definitely had to have common sense and to be mechanically inclined to do this repair otherwise it was easy

Removed old valve easily. New WR57XI0033 valve is designed to mount on lower left, but on mine it has to mount on lower right. Had to drill two 1/32 holes in lower rail to mount the new valve.

Removed icemaker from freezer,
Removed 3 screws from cover plate, and removed screw securing main gear, removed gear.
Pulled back cover plate to expose switches and mechanism.
Removed screw holding switch to remove switch, and installed new switch.
I should have taken a pic of the cover plate, the interior mechanism and the wiring as I went along. It would have saved me 45 minutes in reassembly. Also, as luck would have it, I reversed the wiring on the switch. So off was on, and I had to remove it, switch wires and re-install.
But it works!