10659042991 Kenmore Refrigerator - Instructions

Didn't know if part was replaced from the front or back of door. Removed back/inside first. Good excuse to clean mold found in places not normally seen. The only real problem was getting the face off the dispenser without breaking it. I now know it snaps off from the bottom. To replace one little nozzle you have to replace about 10' of tube. When I pulled the old tube out. I attached fishing line to it and used to fishing line to help feed the new tube through the door.

Parts arrived at 2:30PM.

Read instructions, gathered tools, and went to work. I'd already watched an online video at your site on how to do the repair.

Removed the hinge cover covering the hinge top by using a nut driver to remove the single screw holding it in place. (The video described an older frige and it did not have a screw. I figured that out when I finally went and got a ladder. I had tried to pop it out like the video shows.) There are three screws holding the hinge top in place. I tried using the nut driver to remove the screws but they were pretty firmly in place. I resorted to using my ratchet wrench and that made it easy. (Keep track of your screws, one of mine rolled under a cereal box on top of the frige and I thought I would never find it.)

I had emptied out all the items on the door of the frige, removing the shelves. It was easy to lift the door off of the bottom hinge and lay it on its side against the ladder. At this point I had my son hold the door steady (its kind of unwieldy and 'slippery' when you are trying to remove a screw from the bottom of the door.)

I removed the screw that held the plastic Door Closer, Upper Cam using the nut driver. I used a straight bladed screw driver to pry the old part out of the door (it has an insert for the hinge pin and it had been in place a long time). I also cleaned off the bottom of the frige door (you would be surprised what gets stuck on there - obviously someone spilled oranged juice on the floor and it splashed up on the bottom of the door). The old part had a lot of particle dust that came off it when I removed it. The new part popped right into place and I screwed it back in. The video shows that the repairman had to use a drill and tap set to rethread a larger hole but I just put the old screw back and it held fine. The video also showed the repairman adjusting the Door Stop Bracket but I didn't have to do that, the new cam installation wasn't impeded by the bracket.

I moved to the frige cabinet (again, good to have a second pair of hands to keep track of the door and not let it get damaged while I turned my attention to the Door Closer, Lower Cam. I used the nut driver to remove the screw holdin it to the hinge bottom. It came off easily (it practically fell apart and turned to dust). I placed the new cam and screwed it in using the old screw. No problem.

You could put the door back on with one person but it helps to have two. One to manhandle the door and the other to place it on the lower hinge post.

I put the upper hinge back on and put in the three screws but I left them lose so that I could adjust the door. When I tighted the single screw closest to the door after positioning the door, we tested how it opened and it was hitting the side of the interior cabinet when it closed - you could feel it dragging and it made a clunk/swoosh sound. We readjusted the door using the outside upper corner as a guide and retightened the screw. This time there was no problem. We tighted the other two screws using the ratchet wrench and then put the plastic hinge cover back on with the single screw using the nut driver.

Took us about 25 minutes and made my wife very happy (biggest benefit). The door now 'locks' open and 'locks' closed just like when we bought it and the two doors are aligned (level accross the top) which should have been a dead giveaway that the door closing cams had worn down.

Done by 3:00PM.

First of all, here's a warning to all -- I took the glass shelf / pan cover out to clean it -- with a sponge wet with COLD water and the shelf literally exploded on me. This is the second such incident. Both times I have been lucky and no one was hurt.

The shelf was easily identifiable by part number based on model number. Easy to locate the model number on plate above top shelf inside refrigerator (right hand side in my case).

Only had to carefully set glass shelf in frame -- no issues. I was able to use a screwdriver to remove the shelf support stud and basically pop the replacement back in with no issue.

Thank you Parts Select for your simplified system to order replacement parts, and the speed with which it was received.

Remove side handle from the freezer door ...pop out the black panel from the ice/water dispenser... you need to bend it a little bit to remove... un snap the electrical connections ...the plastic connectors, not from the fridge or the back of the panel,there are plastic connectors (white) in the middle between the fridge & the plastic outside panel.I needed a thin knife to lift the connector snaps to pull the pieces apart. It's not a bad idea to note how they match up so you can put it back properly. unscrew the white panel. There are two screws remove panel.I had to cut the micro switch out of the old style panel. the new panel is much more precise. By the way, if you are replacing the micro switch, it's a good thing to know, there are two. One is for the ice maker, the other is for the water dispenser. You might as well replace both at the same time even if one is working it will save you having to do this again anytime soon.Snap the micro chip into place & thread the wires back through the control panel screw the panel back into the door snap the wires togeather. now test the water dispenser just to be sure. Now arm wrestle the panel back in to the tracks. This is the hardest part. Why it doesn't just slide in is beyond me. Must have been designed by a guy!!! It really is easy & it saved me $300.

I checked the fuses and hoses in the back of the refrigerator to make sure water WAS in fact getting to the front of the fridge. Since the water through the front door worked fine, I had to check the water tube running to the ice maker. It was fine and water was waiting to go somewhere! I decided to pull the icemaker out of the fridge to see what I could fine. Once it was out, I took the ICEMAKER CONTROL AND MOTOR ASSEMBLY off (that's the side part with the dial on it). Only 3 screws to take that off, and it was EASY to see what was wrong once I took that off. There was a connection that was obviously bad (looked almost like it had burned out). My thought was that it was obvious what part was bad, what would it hurt for me to try to fix it myself? When I got online to find the part, PartSelect was the only one that I found that had the EXACT part that I needed, and lucky for me, there were multiple pictures of multiple angles of the part so I could compare and make sure I had the right one!! The part with shipping cost less than the cost of a repair tech to even come out and look at the fridge. Then add the cost of the part and labor if I had the repair tech fix it...I probably saved about $250!!!!

I removed the screw holding the spring steel retainer/clip using a quarter inch ratchet wrench a swivel with a quarter inch socket and a short extention, then just installed the new one. This spring steal through the door ice maker / water despenser lever spring was an easy fix.
I found you by googling appliance repair parts, and found your site really easy to use. I couldn't believe how fast the part came and the very reasonable price. I put you on my web browser's favorites.
Thanks,
Ron

I loosen the screws with a nut driver just enough to pull old gasket away from door. This way the door panel and gasket retainer stay in place. I placed gasket from top and worked my way down one side. It took a little more time to slip gasket under retainer evenly, tighten each screw to keep gasket from pulling out while working around door.
30 minuets tops,never had to turn off refrigerator.

due to over filling and closing the drawers with the door and kicking, the plastic runners broke. Also, over filling the drawers did not help.
AS for the repair, the only difficulty was getting the right drawer in the right spot. Since I replaced both the veggie and meat drawer at the same time, I got them confused. On drawer is longer than the other. other than that, no problem.

First removed the outside cover plate which was some what scary not to break plastic cover. Had read about another discription of removal of cover to start from the bottom because the top is inserted in slots that would have broken if removed from the top. After cover plate removed it was simple to remove the broken parts and install the new parts. The most difficult part to put back in was the spring and rod had to be inserted the same time.

Found the control bracket housing had broken and micro switch for the water pump was not making contact with mechanical link. (In other words when you put a cup under the dispenser and push water did NOT come out.)

I removed the faceplate and switches, removed all the switches and installed them in the new control bracket. Installed new control bracket into fridge and tested. Works! Reinstalled faceplate and switches and drained system for a few minutes. Man I forgot how good filtered water tasted!

Remove the knobs and faceplate to get at the screws behind it. Removing the sensor is a bit involved but everything else is fairly straight forward. See other postings for description / order of operation. Replacement took less than 30 minutes.
Works great now!

I assumed the motor had burned out. I removed the 4 hex-head screws to remove the bracket holding the motor. I had to squeeze the electrical fitting to the motor located in the right rear of the compartment in order to electrically disconnect the motor, since the lower part of the fitting has a latch that prevents its easy removal. Then I could insert a vice grips on the shaft and on the coupling in order to (reverse) unscrew the coupling from the motor. I initially received the wrong replacement motor, but when the correct one arrived, it installed on the mounting bracket easily and I reinstalled the bracket with motor easily. It turns out a new motor did NOT fix the problem, so I'm not sure what to do now.

1. Turn off water supply to refrigerator.
2. Unscrew water nozzle from dispenser.
3. Remove grill on bottom front of refrigerator.
4. Unscrew tubing at the left side of the union.
5. Unclip tubing from the refrigerator frame.
6. Pull tubing out of the dispenser about 6 inches.
7. Cut off nozzle with scissors.
8. Insert 1/4" diameter x 1" long molly bolt about halfway into end of tubing where it was cut.
9. Insert the remainder of the molly bolt into the end of the new tubing.
10. Pull the old tubing through the bottom of the door.
11. When the new tubing is pulled all the way through the door disconnect from the old tubing. Remove molly bolt if it is in the new tubing.
12. Remove the ferrel from the old tubing and use to attach new tubing to the union.
13. Connect the water nozzle to the dispenser.
14. Insert new tubing into the clips on the refrigerator frame.
15. Re-install grill.
16. Turn on water.

I removed the ice maker assembly from the freezer compartment (four nuts/ nut driver) and unplugged the wire harness. I discovered the nature of the problem and I went on the Internet to look for replacement parts expecting I'd have to buy the entire ice maker. When I found PartSelect.com I looked through the pictures of the parts available for my ice maker. I found the correct part quickly and easily. And having an acurate photo on the site, I was able to match all the key features of the mold I had with the one on the screen. I ordered the part, and installed it the day it arrived with just a Phillips screwdriver and a nut driver. It functions perfectly.

The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the cables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)