3639504785 Kenmore Refrigerator - Instructions

Removed four screws at bottom of door, while someone held the door in place replaced the upper cam (there are two) applied some silicone plumbers lube between the mating surfaces and tightened it up. Works like new bottom cam was only slightly worn. P.S. Remove everything from the door first.

My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After working with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!

took top bracket off--then removed door--took
bottom bracket off bottom of door and replaced
door closing cam and reasembled---a piece of
cake

Like the rest of the other statements it was easy with 2 2X4 pieces of wood to block the door up. The other suggestion about buying two of the pieces was a good idea. Once I took off both the top and bottom pieces they were both worn out and it was easy to replace them both at the same time. The door is working good again and shuts on its own.

I blocked the door up with one 2X4 Then removed the lower hinge, installed the closing cam. Then I found that I needed one more closing cam that I didn't order the first time. This other one mounts to the lower section of the door and both cams set together. Re-ordered another cam. When it came in I installed it. Between ordering both parts I had them both in three days. The best to Parts Select
I now know where to buy my parts if needed again.

Thanks
Bob
Sandusky, Ohio

I was set to buy a new magnetic seal to hold the door closed, when I looked it up on PartSelect I saw the recommendation that the problem might be the door closing cam.. I check it with a mirror and sure enough the cam had broken and the door sagged about 1/4 inch. I then followed the instruction and removed the top hinge, lifted the door off and replaced the cam. I did need two and the one attached to the lower hinge had to be drilled out and a new screw and nut attached to hold the cam. It was simple to do, I would recommend selling the door closing cam be sold in pairs with a #10 1/2 inch long screw with lock nut.

I opened the freezer door and removed the access panel, then with a phillip screwdriver,I removed 1 scew and used a pair of pliers to pull the wires off.I then reversed the prosess.EASY

Watched the video very good. Thank You

Video is a great but still need to read the instuctions because there are parts you may need on the old ice maker. Saved myself a bit of money by not having to call a repairman. The process was very simple. I am glad I did it myself. Thank you Parts Select!

Emptied hopper
Removed screws to remove auger from existing
This was so easy I impressed my wife

First i removed two screws that holds the ice maker in, unplug the plug to the ice maker. I was able to remove the old one. Place the new one in screwed in the two screws and pluged in the plug and in just a little while i had ice again. I am a women, if i can do it any one can. I had a repair man tell me it was going to be $250.00 dollars to replace it. I got on line ordered the ice maker and had it in 4 days. Very fast shipping and easy to install. Tina Kearns Beaumont, Calif

Easy

I had no idea how to get the parts easily so i search on web , saw parts select.com,i read main folio of the site.which seems to me very reasonable.just one call and they delivered the part.nicely advised me if i need technical support to fix it but i was too confident and i did it.

Please note that I did this repair 2 times before and it was very easy, it took me longer to get the stuff out of the refrigerator door.

But this time the existing upper and lower cams broke, and the lower part of the door was making contact with the screw that holds the lower cam to the lower support bracket damaging the head of the screw.

Now I could not use a screw driver and I had to use a wrench and a vise grip to hold the round screw head (not easy), and then replace the screw and nut.

I had to insert 2 flat washers under the lower support, to separate the door an additional 1/32 from the ref. base to accomodate the fact that the door gasket had lost its regular shape in the lower part of the door (I discover this when I dismounted the door).

Then I removed the damaged cams, replace them with the new ones and now it is working ok.

Manny

I learned from previous descriptions. Most important is there are two cams so order two. Second is that the door can be blocked from the bottom so the door doesn't have to be unloaded if you are careful. Remove the vent cover. Raise the door as high as possible while closed then block it from dropping down. I used wooden blocks. Remove the lower hinge and bracket on the bottom of the door. Put everythng back and you're back in business. A kit with both cams, spacers, and screws with diagram would have been nice to have.