25357682791 Kenmore Refrigerator - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wiring harness plug, replaced the old timer with the new one, re-connected the wiring harness and reinstalled the mount in position. Hardest thing about it was lying on the floor.

I unscrewed the cover, took out old filter, put in new filter and replaced cover. End of story. Oh...don't forget to turn off the incoming water supply.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Used a ??. The repair was easy took less than 5 minutes

had removed the doors to get fridge in thru small doorway when doors were reinstalled the elbow leak was replaced in about 15 minutes or less by cutting old elbow out of lines and the lines snap into new elbow with just a little force

Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the copper refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.

removed water tray, used a razor blade to brake the seal from the face plate and the fridge, The hardest part was the three screws holding the dispenser face place on where rusted over. I wound up drilling them out. Once the screws removed, a slight lift, the face plate comes right off. I unplugged the cable, and set it aside. Now remove the next three screws, and the dispenser falls forward, (as far as the water line allows) undo the screws leaving the one emplace to hold the ice lever. push up twist. The hard part is getting the new one up and in. just takes a little patients.

Removed broke bracket. Installed new bracket (part #100). Now, everything is O-TAY!

My hand turned the water filter casing around until it unscrewed and then I put in the new water filter.
Screwed the casing tight and I was finished.

Simply unscrewed cover on water filter and pulled old filter out. New filter comes with o-ring on filter. Simply reversed procedure and installed new filter.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Removed four screws at top and two at bottom and pulled ice maker unit out and replaced with the new lever .

Removed outside cover on door despencer, (4 screws) unplug wire, removed unit from refrig and replace rusted thru wire that holds door shut. It was fairly easy. I actually took it apart twice, once for diagnosis and once for repair after the part arrived.

Unscrewed the gaskets from the doors and took off. screwed the screws and put tthe sealant on t he cornors on both doors and that was it. very easy. directions were great.

i removed rhe old storage drawer from the refrigator. removed the front face and slid it on to the new drawer i received from Part Select. put the drawer into the refrigator and it fit perfectly. Part Select web site worked perfectly on selecting the right part. the part was delivered in three days. i would recommend this company for your appliance replacement parts and would not hesitate ordering from them in the future.excellant service.

tony
scottsdale,arizona