25356292403 Kenmore Refrigerator - Instructions

turn off ice maker, unplug electoral connection, under bottom of ice maker, remove two screws (hex) under bottom of ice maker, lift up on it to unhook it, take it out. (dump out all ice ). remove back plate on back of ice maker (two screws), the solenoid is held in place with two brass screws, remove them, then remove ground wire from solenoid and two wires, that connect to it,(make a note of how wires go back !). put it all back together and your good to go. . i dont think its really the solenoid that goes out, its the housing that encases it, and you have to buy another solenoid thats encased. good luck

A little difficult getting out due to restricted space, I took off the fan blade, that gave extra working room. Then it went well going back together,and it all worked as advertised. Thanks. p

Not knowing the history of the refrigerator/freezer and observing that the icemaker would cycle (ice ejector fingers would rotate when the off/on arm was toggled), I concluded that the water valve must have some hard water scale in it which was causing it to stick. I replaced the water valve and the exact same behavior continued. By elimination, I concluded that the microswitch in the icemaker must be sticking. I removed the icemaker, used a hair blow-dryer to heat/dry out the microswitches and then a little shot of WD-40 on the mechanical arms, switches, and cams fixed it.

I used pliers to get the remaining shelf support studs out, then the new ones just snapped right in place. Very easy repair!

I ordered the part from PartSelect using the part number located on the valve itself. The part was delivered in less than 48 hours from the time I entered it. Replacing the valve was easy and went according to the online video instructions provided by PartSelect. The only thing extra was that I had to replace the brass compression fitting on the copper tubing connected to the inlet of the valve. The old one would not seal properly. The compression fitting was about $1.50 at Home Depot. This is my third purchase from PartSelect and I continue to be impressed by them.

1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.

Removed new door gasket from box, installed on three side relatively quickly. The last side took some time, the pair of pliers and wiggling to get it to seal to the door frame.

Took the old one out, put in the new one, and after a couple of days, had a bucket full of ice. I had been fighting this problem since within the first year of purchase of the refrigerator. It's so great to open the freezer door and see it full of ice!!!

I was really impressed with how easy it was to navigate through your website and found the exact part I needed. I immediately received my glass shelf it took all of 2 seconds.

It was real easy took the lines off one by one put them on the new unit one by one same with the three plugs than tighten new unit back on fridge.

took the screw out of the white flange on the top of the door that attaches to the top of the refrigerator. Then removed the cover , and the two screws attached to the refrigerator top. Then lifted off the door removed the bottom plate that is holding the plastic door holder. and replaced the broken part and replaced the bottom plate , set the door back on the hinge and installed the top two screws and the flange cover and the last screw holding the flange cover in place. It actually took longer to type this than the repair

All I did was remove the drawer, remove one screw. I took out the old slide, installed the new one and replaced the drawer. Quick and easy

Put shelf on door, done.

The parts arrived fast, and fit just perfect, they just slide in and snap lock into place. 1 had been broken 2 years ago and I just put off fixing it thinking I would not get the right part, then we broke a seconded one. This web-site made it very easy, and I was pretty sure when I ordered them that they would fit. Thanks for everything

I got the part, hitched it up and it started working right away it fit in easily, and the directions were easy to follow thank you