25338304890 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- TIM from WOODBURY, TN
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The refrigerator light would not work ...even after replacing the bulb.
I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Schenectady, NY
- Parts Used:
- 3206150
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no shelves refrigerator door
Needed to saw the pieces. PUrchased hacksaw.
Son sawed the pieces. Went in like a piece of cake.
Son sawed the pieces. Went in like a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Bay City, MI
- Parts Used:
- 5304464438
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Fridge quit working.
A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from WHITMORE LAKE, MI
- Parts Used:
- 5303324302, 3206166, 3206165, 3206150
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old end caps were broken
Pulled the few end caps off the retainer bars, pushed the new ones in, and used a medium hand strike to seat the end caps in the doors slots.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- earl a from GIRDLER, KY
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light blub blew
unplug power from ref removed old light socket only difference wired a little different checked new socket compaired to old checked terminal ends small big looked at wires big,little plugged up put in new light blub plugged ref power back on work power off pushed socket bac in power on works
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carla from Sumter, SC
- Parts Used:
- 3206150
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Shelves wobble and gasket leaked..
I replaced the shelf end caps in the shelves of my fridge and I also replaced the gasket around the door.
Every time I would open the door, things would fall out because the shelves were giving, because the end caps were broken. Once I got the new ones, I was amazed that these parts are still available and that they lock right in with no problem. Once you get one in, you then have to place one end of that retaining bar into that, very tightly, making sure the end is completely secure in the cap. Then you can lock the other cap to the other end, lock it into place in the door and whala! It is just that simple.
Now the gaket is another story, it is best to soak the gasket in hot water first to draw it up abit so it will be snug and also to use lubricant such as petroleum around the inside where it is going to fit to the door. This made it extremely easy to afix to my door with no problems. I am so glad for this site.. hundreds of dollars saved!!
Every time I would open the door, things would fall out because the shelves were giving, because the end caps were broken. Once I got the new ones, I was amazed that these parts are still available and that they lock right in with no problem. Once you get one in, you then have to place one end of that retaining bar into that, very tightly, making sure the end is completely secure in the cap. Then you can lock the other cap to the other end, lock it into place in the door and whala! It is just that simple.
Now the gaket is another story, it is best to soak the gasket in hot water first to draw it up abit so it will be snug and also to use lubricant such as petroleum around the inside where it is going to fit to the door. This made it extremely easy to afix to my door with no problems. I am so glad for this site.. hundreds of dollars saved!!
Was this instruction helpful to you?
Thank you for voting!
Door handle had too much space between the door and handles.
Use the rubber brushing to fill the gap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geoff from Farmington, NM
- Parts Used:
- 5303324302, 3206150, 215366002
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door shelf retainer bar was missing from fridge door
The replacement part was a bit too long (about 6"). Measured length of the existing bar that was on lower shelf and used a rotary tool with a metal cutting disc to make the same length. Everything snapped into place easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Spokane, WA
- Parts Used:
- 5303917954, 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Temperature in both freezer and fridge sections to warm!
Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Tom Houck
Spokane, WA
Houck Photo
509-723-3418
tomhouck1@comcast.net
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Tom Houck
Spokane, WA
Houck Photo
509-723-3418
tomhouck1@comcast.net
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Sunnyvale, CA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No freezing or cold in either freezer or refridgerator - compressor did not run.
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Pima, AZ
- Parts Used:
- 5303917954
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator keeps frosting up and not cooling
Refrigerator started frosting up and running all the time.I'd defrost it and it would frost up again in about a week.The timer seems to be work so I just guest it mite be the Defrost Thermostat.I removed the duck in the center and back panel in the freezer compartment defrosted it and switched Thermostats and replaced panel and duck, going to lower compartment of the refrigerator.So far it seems to be working a little more time while tell.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Newton, KS
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sadrudin from SAN DIEGO, CA
- Parts Used:
- 218396700
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
The hole on the handle mounting block was too low
I had to loosen the screw holding the mounting block and increase the hole size to fit the screw on refrigerator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from Sierra Madre, CA
- Parts Used:
- 5303917954, 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Coils kept icing and refrigerator stopped cooling lower compartment.
Replaced defrost timer & thermostat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Hudson, WI
- Parts Used:
- 5303324302, 3206150, 215366002
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
The door shelf retainer bar was too long, 6" to 8"
I measured the width I needed and used a handsaw to cut it the proper length. Then I snaped the pieces in and it was a perfect fit.
Was this instruction helpful to you?
Thank you for voting!