3639565482 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cary from ORLANDO, FL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Ice maker stopped working
Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from SAN MARCOS, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Maker Leaking
Researched on internet/you tube; ordered part, and did the repair. Easy to do and saved the cost of a service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FIFE LAKE, MI
- Parts Used:
- WR30X256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Plastic guide in rear of bucket broke it guides auger when dispensing ice
I simply removed 6 screws that held bucket to face and pit on new bucket and put it back in freezer works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmie from Surprise, AZ
- Parts Used:
- 7C7
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb burned out.
Screwed new bulb in socket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from Beaumont, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker was not making ice.
First i removed two screws that holds the ice maker in, unplug the plug to the ice maker. I was able to remove the old one. Place the new one in screwed in the two screws and pluged in the plug and in just a little while i had ice again. I am a women, if i can do it any one can. I had a repair man tell me it was going to be $250.00 dollars to replace it. I got on line ordered the ice maker and had it in 4 days. Very fast shipping and easy to install. Tina Kearns Beaumont, Calif
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from LIVONIA, MI
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Maker Clogging up from frost build-up
Turn off power
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Wesley Chapel, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
froze in freezer
unclipped and replace with new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joselito from riverview, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Building Up In The Ice Dispenser Chute
Under the control panel there are three small holes. Insert ballpen or small flat screw driver on both outer holes to push a tab lock that holds the control panel in place. Then pull out control panel and three set of wires will be exposed and disconnect wire connectors (connectors have different sizes so you wont get confused in reconnecting). Unscrew four screws on each corner that holds the ice dispenser assembly (a part where you push your glass against to dispense ice or water. The flapper is exposed and easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Hillsborough, NJ
- Parts Used:
- WR72X210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the plastic slide cracked wouldn't support drawer
Super simple! Hardest part of the entire process was identifying which part I needed to order. Once I received the part (which shipped promptly and was at my front door within 2 days), all it took was 5 mins and a screwdriver and I was back to having a usable snack drawer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JACOB from COLLEGEVILLE, PA
- Parts Used:
- WR62X23154
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Only crushed ice. No cubed.
Found a step by step video on YouTube made replacement very easy. Cubed ice is back. Time for a cocktail to celebrate!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phil from MADISON, WI
- Parts Used:
- WR30X256
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken plastic on ice hopper that helped stabilize the auger
Emptied hopper
Removed screws to remove auger from existing
This was so easy I impressed my wife
Removed screws to remove auger from existing
This was so easy I impressed my wife
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from River Edge, NJ
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker discharge was slow and jammed with ice and frost. The cause was a distorted flapper that did not seal properly, admitting warm air into the dispenser chamber.
Excellent video was available on the Parts Select website. It was simple. The selector panel pulled out by hand from the bottom. The subpanel was removed with the four screws. The flapper snapped out of the holder with two clips. The new one was inserted in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- salomon from dallas, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers
flapper gaskeet dried out
The video to replace the flapper looks easy, howerer the first step is to remove thestic cover of the icemaker. In my refrigerator model (as oposed to teh one shown n teh video) teh coved if firmly attached and goes under the refrigerator external plate so I was never abel to take it oot (so step 1 failed).
I was able to replace the flapper TROUGH the whole whre te ice comes from! this took lots of patients and someone with small hands!
I was able to replace the flapper TROUGH the whole whre te ice comes from! this took lots of patients and someone with small hands!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clayton from TUCSON, AZ
- Parts Used:
- WR62X23154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice crusher did not work, Ice would plug in tub chute on discharge end.
Pulled ice tub, removed auger rotation motor and solenoid housing, removed solenoid and replaced with new one and reinstalled. Checked solenoid was working by holding freezer door open and closing switch to door an activating ice switch-- solenoid picked up. Put ice tub with auger back into freezer.
Was this instruction helpful to you?
Thank you for voting!