1068490082 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Victor from Colton, CA
- Parts Used:
- W10822278
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The refridgerator will not run
After the front panel was removed, disconnected the timer and installed new in reverse order. The provided instructions could be more straight forward, I spent more time reading it than the installation itself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecelia from Garden City, TX
- Parts Used:
- W10822278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer made lots of Ice and Refrigerator didn't cool
The Defrost Timer is located in Refrigerator section (not the freezer) where your temperture guages are. Move panel and replace the non working Defrost Timer with the new one. It took my husband about 30-40 mins to fix. This was about 2 weeks ago and my Freezer and Refrigerator are working like new. I bought this Kenmore Reftigerator brand new in 1996 and I lost the manuel to it. Thanks to my daughter who found the Defrost Timer on the Internet, I thought I was going to have to buy a new one. This was real easy to fix. The instructions that came with the part was easy to understand and very self explanatory. It also had very good diagrams to follow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dewey from TOMAHAWK, KY
- Parts Used:
- WP2198202
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Refrigerator was not cycling on and off properly, allowing food to thaw.
I followed the directions given in the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stefan from BLOOMINGBURG, NY
- Parts Used:
- WP2198202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Thermostat stopped working. Only cooled at highest setting.
Repair video was excellent but thermostat unit was slightly different then original. Fortunately guessed right regarding connections. Also very difficult to place the insulating plastic on wiring. Not very smooth. Also removing panel was different then in video. Needed to remove the panel to reveal two screws underneath that need to be removed along with the ones at the ceiling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Fallbrook, CA
- Parts Used:
- WP2198202
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Frig did not turn off (stay running all the time) but originally did not run until I wiggled the temp nob
Just followed the Video I found on your site. Seems to work good now, took awhile to get temp setting correct (had to set it a little colder about half way between the "b" and "c" setting).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from RED WING, MN
- Parts Used:
- 4388538
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Broken support on lower drawer shelf.
Important: Do not twist broken stud to remove if possible, just pull with the pliers straight out. I twisted it and made the hole larger. Even so, I just used Gorilla Epoxy glue to secure the new one (follow directions on the package) and it's fixed. It's been a couple days and still looks secure. Thanks for the quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Milton from NEW YORK, NY
- Parts Used:
- WP2198202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
needed termastat
your video made it very easy...Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from INNSBROOK, MO
- Parts Used:
- 4386774
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
One of the front wheels was broken in half.
Very easy. Left the front of the refrigerator so it is approx. 4 inches of the floor. (used a two by four. Removed the screws (one for each roller). Removed the rollers and replaced with new rollers. Reinstalled the screws with secures the rollers to the refrigerator. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karl from BIRDSBORO, PA
- Parts Used:
- W11581579
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Shelf studs broke several years ago and I had a problem locating them. Finally wised up and checked Part Direct and found them, ordered the kit w/ 12 pieces. Then quickly watched the installation video. Took less than 30 minutes to replace two different studs. Wife is very happy.
Simply took broken pieces of old stud out and replaced with the new ones. Used pliers to adjust them. Replace a freezer stud and a fridge stud.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from REDDING, CA
- Parts Used:
- W10822278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Warm refrigerater
Followed instructions from ideoo
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from GLOVERSVILLE, NY
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Plugged it in.
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAUL from MIAMI, FL
- Parts Used:
- 4388538
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Wrench set
the broken stud was very hard to remove, no instrucitons anywhere
only the front right stud was broken with very little left attached to hold and remove. After a long twist and pull , got it out and placed the new one....
Still recommend Part Select..RAUL, MIAMI FL
Still recommend Part Select..RAUL, MIAMI FL
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CARROLLTON, GA
- Parts Used:
- WP2198202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Freezer would go from zero to 55 degrees. Ruined all my food.
Followed instructions in video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from HELENDALE, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
freezer would not freeze
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricky from PALOUSE, WA
- Parts Used:
- WPW10662129, WP2198202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The unit would run fine, cool to set temp. then warm up and not restart. Used your trouble shooter and it recomended replacing the capacitor.
Replaced the capacitor per your video. Tested and the problem persisted. Next replaced the thermostat per your video. Tested and the unit functions properly. The challenge was the connector locations on the new thermostat were different than the original. Front and back instead of top and bottom. I could not find an answer for wire installation. So I guessed and placed the double red wires on the spade closest to the door and the single orange wire on the rear spade. It worked this way and I did not try it the other way. Fridge is working and my wife is happy. Regards, Ricky
Was this instruction helpful to you?
Thank you for voting!