59653469300 Kenmore Refrigerator - Instructions

Pressed in the end of the filter cover, lowered it down part way. Twisted the old filter 1/4 turn and removed it. Set in the sink to drain. Inserted new filter and twisted it to lock. closed cover. Done. Total time @ 1 Minute.

Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of connection held the other two attachment points along the long edge of the icemaker. I did not have repair manual or useful drawing but looked @ PartsDirect pic of side brackets & used a small mirror to confirm that mine were also some sort of "snap in" attachment.
Remove icemaker unit by pushing upward and outward on the unit. I takes a good bit of pressure and will pop loose, but be careful not to break attachment bracket from freezer wall.
Scavenge shut off bar and wiring harness from old icemaker once you have it out & attach to new one before installing it back in freezer.
Again, you might find a mirror useful to align those pesky snap-in brackets with the new unit.
Since you probably kept your freezer running while waiting for the part, the plastic snap-ins will be cold and brittle. I warmed them up first by applying a dampened cloth heated in the microwave to make them a little more pliable.
A good push of the new unit towards the snap-ins along with some upward force will get it stable.
Reattach the metal screw in bracket & connect the wiring harness to rear plug... and don't forget to plug the whole thing back in.
It will take awhile for the first batch of cubes dump as the timer may need to cycle completely around to get to the fill cycle... be patient.
Dump the first couple of batches of cubes just to make sure you're free of any residue.

unplugged refrigerator and shut off water, removed one screw and loosened two more, after removing one side of the ice bucket rail, unplugged electrical from old ice maker. Then I removed the bail and out on new one, reinstalled ice maker in reverse order from taking it out.

I removed the screws in the lower back panel where the compressor is located. Then I unplugged the capacitor and plugged the new one in. I then checked to see if the compressor would start. It wouldn't so I replaced the overload relay with capacitor and that fixed the problem. The capacitor just plugs into the relay then plugs into the compressor. There are several screws but all in all it is easy.

My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: one of the three screws that hold the ice maker to the refrigerator wall is hidden behind the large (black) end of the ice maker and is difficult to access. Before trying to replace the ice maker, make sure you have the physical dexterity to remove that screw. Second problem: it is not apparent how to remove the wire harness that plugs into the ice maker assembly. BEFORE you can remove the wire harness, you MUST remove the large white cap that covers the black end of the ice maker assembly and then push in a retaining tab to release the wire harness. If you don't do this, the wire harness will not release. Other than those two problems, it was relatively easy to remove three screws, unplug the wire harness, transfer three small, metal parts from the old ice maker to the new, plug in the new wire harness, mount the ice maker assembly so that the water tube is in the proper position, and then re-install the three screws. The ice maker works fine now. (P.S. I was told by an expert that the real problem might be a malfunctioning fill valve. I would have replaced the fill valve if replacing the ice maker assembly had not fixed the problem.)

Parts were available at the locat applicance store, but the cost was 20-25% higher than ordering through Parts Select (including shipping) + it was delivered in 3 days right to the house.

Removing and replacing the ice maker was fairly straight forward. Tight quarters to work in, but managable.

1. With the freezer turned off, uplug the ice maker power cable at the back of the freezer.
2. Remove the four phillips head screws and ice bucket rail to the side of the freezer. I found it was easier to re-install the new ice maker with the rail clear off.
3. Loosen the two upper hex head screws holding the ice maker (requires a nut driver).
4. Lift the ice maker up and off of the upper screws.
5. With the ice maker out of the freezer, remove the power cable from the old ice maker and re-install on the new ice maker. At this point, both the front cover and the on/off lift bar can be transfered from the old ice maker to the new one.
6. Slip the new ice maker down over the two upper screws making sure the lower mounting tab is behind the ice bucket rail. Make sure the hole on lower mounting tab lines up with screw hole.
7. Re-install the ice bucket rail and tighten all screws. Make sure the water supply tube is lined up correctly feeding into the ice maker.
8. Re-connect ice maker power cable at the back of freezer and turn freezer back on.

It took about 4 hours for the first ice to generate. It cycled normally after that. No more leaks or ice globs in the ice bucket.

By sliding the drawer out and lifting it up at the end, the drawer will come right out. By installing the new drawer in the same sequence, the job is completed. As for the filter, it is located inside the refrigerator compartment on the upper right side.Simply remove any items from the top shelf that may be in the way, and then push in on the tab that extends out from the filter housing. The filter and connector will swivel down at that point,simply hold the connector in one hand to stablize and with the other hand, twist the filter counter-clockwise to remove the filter. To reinstall the new filter, remove all protective covering from filter. Plase filter against filter connector and turn until tight (1/4-1/2 turn).Raise complete assemble upwads until tab snaps back into place. Installation is now complete, next purge the air out from water supply by placing a pitcher or other large container under the dispenser and activate.Run water for a minute or so until all air is removed.

I removed the drop-down outer housing by gently prying the sides of the two pivot pins at the rear. This gave me move 'room' to grip and slightly rotate then pull the old filter forward and away from the tight suction connection. I was concerned that I would be too forceful for the plastic assemblies and would break something; deliberate motions and a steady thought process on the problem helped disengage the darned old filter!

The switch-out of the water filter was simple with good instructions on the box.
The part was delivered very, very quickly!

I unscrewed the old one and replaced it with the new one. The real benefit was I got the exact part I needed w/o a 30 minute drive and sales people that ignored me. I had gone to the local store the day before and come home with the wrong part because i could not get assistance and the part # I had did not match what was labled on the package. I used the same part # on the website and got exactly what was needed, less that 48 hrs after I ordered it. thanks for the prompt service. we will be a repeat customer

After emptying the refrig. door, I unscrewed the plate on the top of the refrigerator that covered the door bolts. Then off with the three bolts. I removed the door by lifting it up a few inches. The two parts of the door cam were easily removed and replaced with the new part. BEFORE REPLACING the door spread vasoline on both cam parts.
(Not after as I did. The second time you do any of these repairs go SO much better :o)
After putting the door back on, adjust the tension of the screws holding the door in place if needed to align the door on the cams so that it shuts completely. Failure to do this will require taking the top off the door again. (see comment above on "... second time...")
If all is properly aligned, the door should swing completely shut.
Even with the mistakes that required removing the door to lubricate the cams, and removing it AGAIN to readjust the screws on the top to properly align the door on the cams, this was a twenty minute job. My wife and I were still speaking to one another at the end of it- a sure sign of an easy repair.

Installed new ice maker. It was easy - loosen two screws and unplug old wire harness. Put new unit in place. Did not realize new unit would not come with wire harness, but transferred old one to new ice maker (easy) and, "voila" some ice in 24 hours -- much ice since then. I am a 68 year old woman and it was "sort of fun" doing this job.

Well the frist thing I did was get out the all the paper work and look under trouble shooting.This frig has a list of codes to try to help narrow down what parts might be bad.Well at frist it seemed it was a Defrost Thermastat?Well thanks to PartSelect it showed me right where it was and step by step how to remove and replace it.It took me over 2Hr's,after that I let the frig run all night and the next morning(yep warm frig)not the part I needed,well now Im mad,the local part store said you need a 3in1 jump starter easy to in stall at $50.Can'nt bring parts back no way weather thier opened or not.So get home and can'nt see how this jumper is going to wire up to my compresser?So on to the Web site to get some info,find out that this part gets a thumb's down,it puts out more volt's then needed and kills your compresser the reviews where very help full.So back to PartSelect to see more info,then I spoted the Overload/Relay and went to the back of my Frig and this part just plugs right into the compresser,I pulled it of with pliers and Bingo a burn spot melted right through the Overload/Relay.Ordered the right part the same as the old one.Put the part in and Bam,compresser fired right up.If I only did alittle more home work I could off saved alot of head ach and money.Thanks PartSelect I'll alway's click on to your web site for future parts and advise.

I didn't know what the plastic was - just that it was unappetizing. Reading other posts, it must have been the teflon coating. The refrigerator is 13 years old and reading other posts, I guess I'm lucky it lasted that long.

My boyfriend did the repair and here is his story:

The first ice maker we received was cracked on one corner. Not knowing how it got that way, I was concerned that there might be additional internal damage and that the unit wouldn’t work properly. Part Select was contacted and a replacement unit was sent with no difficulty.
As other reviewers have said, the replacement was quite easy, taking less than half an hour. The only tools I needed were a screwdriver and a nut driver. To begin, unplug the refrigerator and turn off the water supply to the ice maker. Loosen, but do not remove, the two top attachment screws. Then remove the bottom screw. Lift the unit up off the top screws and remove the water inlet hose at the top right. It’s probably a good idea to have a container handy to catch the small amount of water that comes out, but you’ll need a third hand for this.
The electrical wiring harness is very short and may be tricky to disconnect. On my refrigerator there is a round vinyl connector that plugs into a receptacle on the back wall of the freezer compartment directly behind the ice maker. This was removed with no difficulty (accidently, actually). Once the unit is out of the refrigerator you can remove the connector from the ice maker by using a screwdriver to depress the latch tab that is visible in a window in the unit housing. When installing the connector in the new unit make sure it is fully seated. Next, reconnect the round vinyl connector to the receptacle on the back wall of the freezer compartment. This was the worst part of the whole procedure. You have to support the unit close to the back of the freezer (due to the short harness) with one hand while inserting the connector with the other. This requires both arms in a confined space. The first time I did it I apparently didn’t get a good electrical connection on one end of the harness, and it didn’t work. Because the connectors are directly behind the ice maker I had to remove the unit and re-install it, but it was much quicker the second time, less than 10 minutes.
Once the connectors are in place put the water inlet hose into the opening at the top right. You may need to re-use the retaining clip from the old unit for this. Slide the two top mounting ears down between the screw heads and the back wall of the freezer compartment and tighten the screws. Then install the bottom screw. Plug in the refrigerator, turn on the water and make yourself a frosty beverage.
All in all, a relatively quick and painless procedure.

Another note - we kept saying "is there ice yet"? I think the metal bar that controls the ice maker needed to be raised and lowered a few times before it would work properly as it seemed to raise 1/2 way but the ice would not drop so I put it down and it worked its way up. Had to do it a couple of times over a 4 hour span but once going, it is working like a champ.

unscrewed to removed old and screwed in new