25338627894 Kenmore Refrigerator - Instructions

The only problem I had was that the end cap was sent before the rack. This refrigerator is in our cottage and I brought up the end cap while waiting to receive the rack. I couldn't remember where I put the end cap, so when the rack came it took me a few weekends to find the end cap. Once I did, it took me less than 1 minute to repair. I put the rack on the end caps & pushed the end cap in place. DONE!

End caps snapped out of door,
Replaced with new caps

First i pulled the crossbar off the door, then I pulled both end caps off the crossbar and then I
put the two new end cap on the crossbar and then tapped snoggly into place with the palm of my hand. Job done. took all of about 5 seconds.

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

just like the video showed...it was excellent!!!

After testing and eliminating the temperature control and the timer as the problem, I turned to the thermostat. I had to wait for the ice buildup to thaw and then could remove the rear freezer panel (this was the 3rd time: first, to discover the ice buildup causing the problem, second when it came back after a complete thaw and test the thermostat, and this time to put the Partselect thermostat back in). My thermostat was visibly damaged from water melting into ice and expanding the casing and eventually breaking one of the connections. I connected the thermostat connection wires (not recommended) to get by while ordering the part, which shipped faster than local repair places could get it from their warehouses, and at a fraction of the cost. I'm really impressed with partselect's fast service and all the knowledgable customers who have explained how they installed them. I now have an intimate knowledge of how my fridge works and saved hundreds in repair, or twice that in replacement. Thanks!

It snapped in place.

Ordered the parts from the product discription (photo) as well as chart showing actual size. Got the parts( in two separate shipments) cut the bar to length and snapped them inot place. Bingo!

removed screws with from the back panel of the freezer; located defrost thermostat attached to coil with a metal clip; unplugged thermostat and replaced with the new one. Put every thing back together and it works perfectly.

We replace the end pieces to hook the holder back on the door.

Parts Select is an excellent source for help and parts identification. I highly recomend them.
My first option was to replace the defrost timer.
After still getting ice and frost buildup in freezer I decided to replace the defrost thermostat.
Remove all shelves. Losen icemaker if applicable. Remove light cover and bulb. Remove all screws securing rear vertical cover. Carefully move back panel, disconnect icemaker and bulb assembly. carefully remove styrofoam cover at upper left and remove defrost thermostat. I tested the thermostat and found it was defective. It would not close circuit after being placed in a working freezer. Reverse procedure to replace thermostat.
This solved the problem

took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

All I had to do was change out motors, and the fam would spin right,and the freezer was alive again. With your older models you may have to re-mount the motor bracket in the back for the fan to clear,due to the fact that the motor sits alittle lower than the old model

I found this website via a google search and clicked on the link suggesting solutions for the symptoms I had. I decided to order the part (defrost timer) that was proven the larger percentage of time to fix my issue (warm refrigerator) but decided to also purchase the evaporator fan motor as it was suggested by my brother to replace it as well. We powered off the refrigerator and removed the back wall of the freezer and completely defrosted the unit. This seemed to be the most work and longest time to complete. We used a hair dryer to do this. Once the ice was gone, we replaced the defrost timer, which seemed to fix the warm refrigerator part. We didn't immediately swap out the evaporator fan as the power plugs did not connect properly and it was a little confusing on how to accomplish this. I called partselect back and they didn't have anyone that could talk to me throught the replacement process but recommended we call frigidaire. Meanwhile, we found out that the defrost timer corrected the warm refrigerator and now that the evaporator fan could move (no longer frozen in ice) it was making a lot of noise. So we contacted fridgidaire, and they were able to provide me with a similar video on connecting the power between the new evaporator fan motor and the refrigerator. . We ended up snipping both power connectors (from fridge and new part) and twisted the wires togehter and now the fan is moving without noise, the freezeer and refrigerator is working like a champ! Very happy outcome!

Replace evap fan motor. Take a close-up picture of the evaporator fan motor installation prior to removing. Take pictures as removing various components.