25358685893 Kenmore Refrigerator - Instructions

Found that that ice maker was working mechanically and electrically but was not receiving water to the ice maker. I found that the dual solenoid valve was not sending water to the ice maker when I asked for water so I ordered a new dual solenoid and this fixed the problem,however I also found the water feed tube was frozen and had to take it off an thaw it out. Now the ice maker and water dispenser is working great.

i removed rhe old storage drawer from the refrigator. removed the front face and slid it on to the new drawer i received from Part Select. put the drawer into the refrigator and it fit perfectly. Part Select web site worked perfectly on selecting the right part. the part was delivered in three days. i would recommend this company for your appliance replacement parts and would not hesitate ordering from them in the future.excellant service.

tony
scottsdale,arizona

Checked for continuity in heater, defrost thermostat and defrost timer. Heater good; not sure about thermostat or timer. Replaced thermostat - no change. Replaced timer - rotating and heater working.

I called the repairman who diagnosed the problem as a thermostat then had to order a thermostat took about 2 weeks to get back and install (cost little over $100). did good for about two weeks and same problem reoccured. I decided it was defrost timer and ordered from this site for $19.95 including shipping. I got on ( you tube ) and got instructions(recommend you tube) for DIY install about 15 to 20 minutes. Has been running great for about 3 weeks. ( YOU TUBE IS GREAT FOR A DIY REPAIR ON ABOUT ANYTHING)

Ice maker is held by 2 screws just above the unit, on the wall of the refrigerator. You can't see the screws, so borrow your wife's makeup mirror. Shine a light into the refrigerator, and using the mirror, locate the two screws, holding the unit in place, on the wall of the refrigerator. Using a nut driver, or socket wrench, with a 1/4 in socket, loosen up the two screws, but don't remove them. Bump the unit upwards, and away from the screws. (BEFORE doing anything!! Shut off the water supply, unplug the refrigerator) When you get the unit freed up, just unplug the old unit, and install the new one. You don't even have to worry about the water lines, and you'll see why, when you get the old unit off. Just reverse the procedure, installing the new unit. Very Simple, 10 to 15 minutes tops.

The repair was extrememly easy and took about as long as it did to order the pasrt online. Just removed the front drawer handle with a screw driver ,slide it onto the new storage drawer and reinstall. Less than 5 minutes.
C.J.
Rochester Hills,MI

I took everything out of the freezer. Removed All the shelves, took the front off of the evaporator coil compartment. Then I defrosted the evaporator coils with a blow dryer because they were basically a solid block of ice. Then removed the heater coil, installed a new one. Installed a new defrost thermostat. Put the evaporator coil panel back on. Then I turned the thermostat back up to where the fan came on and I noticed it took a few times for the compressor to continue to run. I don’t know what that was all about but eventually the compressor kicked in and everything worked like it should.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Changed the defrost timer and the Thermostat. Still did not fix the problem. Replaced the defrost heater and now it's cooling just like new.

Jonnine's husband did the repair - At first, I was stumped on the cause of the problem because I thought because I did get some ice, the pump (valve) must be working. But after pulling the dust cover back off the bottom of the fridge, I removed the dual valve. I had my wife operate the switch in the door for water and I could tell that it wasn't activating the valve at all. Ordered the valve, took 30-45 minutes to put it on. Worked like a charm. Full ice bucket now and water through the door again. Easy install.

Removed three screws from cover to gain access to the two mounting screws on the water filter housing assembly. How to remove the water line connectors took the most time as I had not seen that type of fitting before. Other than that it was drop dead easy.

First I removed the plastic grill (pulled out, no screws) from bottom of refrigerator, then I removed electrical plug & two screws from old timer (timer located on the front inside left lower side of refrigerator). Installed in reverse order.

First I unplugged the appliance for safety,then I proceeded to remove the sheetmetal from inside, the freezer compartment, this is where the evaporator is located and where you will find the defrost limit switch or thermostat same thing. also the defrost heater is located here as well. I made note of what plugged into what and what the colors of the wires are for future use. You also need to check the defrost timer which on this unit, it is located in the very front lower left coner of the appliance. Once I received the parts I put things back together in the reverse order, plugged in the appliance and so far so good the refrigerator is cold now.There are a lot of repair manuels out there that will help you repair your appliances and save yourself a lot of money. You just have to be willing to do it yourself.

Remove ice pan below ice maker. Got mirrow verifed the type of screws. Obtained nut driver and felt it at right angle remove screws only have way. The ice maker lifts up and off. Took needle nose pliers to grip and remove electrical connection plug. The instruction and picture sent was no help the picture were the size of a thumb nail no detail could be determine. I installed the adapter plug and all the extra length wiring was the most difficult to type wrap with both hands extended out in front. I finally wrestled it in on to the two screws unscrewed from the wall about 1/2". Keep the ice maker water lever up and ensure it aligns to the water trough inlet. Works Great.
glg

Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.