25370137991 Kenmore Refrigerator - Instructions

Removed the back panel in freezer compartment with the nut-driver. Then I cut off old thermostat connections, and spliced in new thermostat connections (repairman had already replaced defrost timer, and said not to trust connectors included on wires-they failed often). Then I snapped thermostat itself onto cooler coil. So far so good, fridge is running at 35-40 degrees a week later. Thanks Parts-Select!!!

just had to loosen the old, broken piece, and snap in the replacement. Piece of cake

Had to remove all screws on rear back cover of freezer inside, unplugged refridgerator, uncliped thermostat, unpluged thermostat. Replaced thermostat with new one in the same location, and let defrost fulley. Reassembled, pluged in, and tested. All was good. But I did also replace timer at first part of the repair so I suggest you replace both at the same time.

removed freezer door and installed the new one. This was a pretty easy thing to do, although putting the old handle on the new door was a challenge. No knowing that there is a plastic piece holding the top of the handle i broke the that piece and had to order another one. Mean while the freezer was making alot of frost inside, so that had to be cleaned after the new part came.

Loosen two screws, unplug power, lift it off, put new one on and make sure water chute is correct place, tighten screws!

All I had to do was remove the original support that was on the inside wall of the refrigerator, which I had to use pliers since there were broken pieces, and then I just snapped the new one into the three holes provided for this support. The crisper drawer works fine now. It literally only took about 1 minute.

Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.

I removed the shelves in the freezer, took out the five 1/4" screws and lifted off the cover. It was a simple matter of using a blow drier to remove all the ice, then unplugging the two wires and unclipping the thermostat from the upper cooling tube. Then clipped the new one on and reconnecting the two wires.

Works great!!!

We love our ice here. I seem to replace the ice makers one to two times a year. Generally the ice cycle gets off for some reason and it starts making loud popping/clicking noises (gear grinding). Its easy to replace. Simply loosen two screws holding the unit to inside of freezer and disconnecting the wiring harness. Unit slide up and out. Replacement is super easy (5 mins or less). Bam! Ice!

Purchased a new ice maker assembly and installed. Very easy

This refrigerator is less than 2 years old. I have had to replace the ice maker 2 times now. Cheap ass parts! Only one ice maker you can order so just be prepared to replace it yearly!

removed ice maker storage holder and then remove two philip screws and unplugged four pin connector. removed ice maker and installed new one . very easy to do

The instructions that came with the replacement icemaker were very complete, in particular concerning the small levelling bracket on the bottom of the icemaker, because the old bracket needed to be removed from the old icemaker and transferred to the new one. This part of the installation might not have been obvious, so I was glad to see it clearly outlined in the instructions. The old icemaker was removed by loosening two nuts and detaching the electrical connector, and the new one was installed in its place. Fairly simple, the whole job took about 45 minutes because I work slowly and carefully. A more confident person could probably have the new one installed in 15 minutes. Only drawback: about three to four weeks after installing the new icemaker it has begun making a loud clicking noise on occasions. It is a repetitive (5 second interval) clicking, and only happens for about a minute every few hours and then stops. I am concerned that it might be gears prematurely wearing out and slipping. I guess I'll know in a few weeks if this one stops making ice.********************************************* Update: after about 9 months the new icemaker quit working and will need to be replaced. I removed the front cover from the icemaker and could clearly see that the teeth of one of the plastic gears were worn out and no longer meshing with the opposite gear. The drive gear was just spinning in place and making no contact with the larger gear.

After realizing the engineering on this dryer was different, I was able to access the temperature control thermostat through the front, along the side of the heating element. Several philips screws hold the front on, removing them allows you to take front panel off. At that point the heating element is below. I took a picture of the wires, so that when I started removing them, it would be easy to reconnect. Two screws hold the heating element in place, upon removing the heating element housing pulls gently forward and out, be careful of the wires, the thermostat is the second thing connected to the housing of the heating element. Two more philips screws hold the housing to the bottom of the dryer. Two wires are removed from thermostat, which is also held in place by two philips screws. Remove wires, one at a time and place on thermostat exactly as they were on old thermostat. Hold new thermostat in place with the two Philip screws, and reassemble in reverse order. And enjoy your working dryer once more, hopefully for years to come.

loosened 2 screws with 1/4 inch nut driver, disconnected electric connection lifted old ice maker out, replaced it with new one hooked up electric plug tightened 2 screws