2539301761 Kenmore Refrigerator - Instructions

loosened two 1/4 in. screws removed ice maker unplugged harness. Plugged back in slid the replacement ice maker over the two screws secured. Done

first replaced dual solenoid, then ice maker. still not working. going to chase electrical next

It was fairly easy to replace the thermostat. Unplug the refrigerator first. Then remove the refrigertor light bulb and 3 screws on the plastic cover that houses the thermostat and defrost timer. Unplug the thermostat from the wiring on the refrigerator and remove the plastic housing holding the thermostat. Remove two screws holding the thermostat and replace with the new one. Put everything back together in reverse order. Unfortunately, this did not corrrect my problem. The refrigerator is well over 30 years old and I had narrowed down the problem to the thermostat because the old one was hard to turn to adjust. About 10 years ago, I replaced the defrost heater in the rear of the freezer compartment for the same problem, and didn't think that would be the problem this time. Well, as it turned out, I checked the resistance on the defrost heater and it was was bad again. I replaced the heater this week I got from PartSelect, and the refrigerator cycles fine now. Replacing the heater is a little more work that changing the thermostat. You have to remove the freezer compartment fan, fan vent, and back inside wall of the freezer section to expose the coils and the heater element. You just need a socket screw driver. Then you have to reach inside and unplug each end of the heater to check it with your ohm meter. A bad element will show up as an open circuit. Then to replace it, you have to maneuver it around to get if away from the coils and remove a couple of clips. Anyone with some common sense can do it, but it can be a bit challenging.

Followed the video instructions posted below the product. Its a tight area to work in but it can be done. It did not immediately start making ice. I waited and waited.... 3 hrs 4 hrs still not filling up or making ice. Finally I decided to pour some water in the tray and see if it would freeze ice and dump it. It did and immediately started to fill up on its own after that! Its been working perfectly ever since! So dont be alarmed if yours doesnt work immediately and try pouring some water in it if yours doesnt being working within several hrs. I am happy I was able to do this myself and save repair man costs. Its just not work the cost they charge for older appliances.

Unplugged refrigerator. Removed control knob and cover. Unwired control and removed same. Removed plastic tube from old capillary tube and placed on new unit. Installed and wired in new unit, making sure new unit was in the "off" position. Plugged in refrigerator, turned control knob to the first numerical setting, and was rewarded with the startup of the refrigerator compressor. Voila!

The two screws that held the ice maker in place could not be seen do to there location. I could only get one hand inside do to space restriction.So I placed a mirror inside so I could see the screw heads and from point it was very easy to see and line up the nut driver on the screw heads. I then lifted it up and unplugged the wiring and installed the new ice maker. Works like a charm. Paul

This is the 2nd ice maker replace in the past 20 months. This installation was easier following the experience of the first replacement. The instructions are well written. The pictures or illustrations are difficult. The most challenging part of the installation is routing and fastening the wire harness. The illustration was not helpful. Overall, this is a repair most DIYers should be able to accomplish.

ice maker= replaced overload,microswitch and solenoid water valves.refrigerator=replaced the thermostat.Great price on parts,very fast delivery and parts were a perfect fit.You made the job very easy. John

Took front off and found the broken spring, got new one and replaced, now works great. Make sure to unplug as the water can come on and flood the freezer.

Called a repair man. He said it was a a sensor type valve at the bottom back of fridge and he would have to order. He never called us, so we went to website and ordered it. Replaced it. It WAS obviously burned out/dicolored. Bracket had to be redone, as it wasn't standard. Didn't work. Ordered new icemaker. Worked like a charm. Video for installing icemaker very helpful. He called a couple weeks later and we already had it fixed.

Replaced ice maker - easy to replace but it did not fix the problem.

I watched the video and it seemed pretty easy. I ordered the new ice maker. It arrived in 5 days and I chanted it in less the 30 minutes. A little tricky seeing where you have to loosen the screws but not hard. and in 2 hours I had ice again.

1st my 72 year old husband has not had great success in repairing anything: electrical or plumbing. We got the part the next day. Had ordered it late one afternoon and had it the next morning in Wyoming. From the time we took it out of the box, disconnected the old one, plugged in the new one, remounted, it took less than 15 minutes. Amazing and it works great. Didn't need extra electrical connector, but tricky part on electrical connectors is to squeeze side to take apart and put back together. He used mirror to see the screws to loosen to take out and put back in ice maker. Next day our tray was full of ice. Good service/Good Product.

instructions were very simple. Took about 10 minutes to replace the unit. Do NOT get excited about immediate ice because it took mine awhile to g et cranked up for full production. Anyone can do this! Saves about $150.00 in labor to have someone(no smarter than you) do it for you.

We reviewed the video posted on your site for guidance. It was very helpful to see someone do the repair. The project went just as described in the video. Within 24 hours I had a full bin of ice!