2539628020 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- joseph from ridgwood, NY
- Parts Used:
- 5303207230, 5303207229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken-door shelf retainer bar end caps
i simply snaped one end cap in put retainer in on sie put other end cap on retainer then snaped end cap in place --job done parts where perfect thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOYCE from CHICAGO, AL
- Parts Used:
- 5303207345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gasket was worn
Removed all the screws. Replaced the gasket put all the screws back. This would work great if the door wasn't out of alignment.
Now I have a new refridgerator coming on Monday.
Now I have a new refridgerator coming on Monday.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andre from ANDERSON, SC
- Parts Used:
- 216594300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Freezer was not freezing.
I removed the compressor start relay and replaced it with the new part. Initially it did not work. When I checked my work, I had to tighten the connector on the new part. Once I made the correction, the freezer is freezing normally again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gaynita from Philadelphia, PA
- Parts Used:
- 5303207345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door gasket was ripped and food wouldn't stay cold
First I removed the old gasket by pulling it off the door. Then I removed the screws from the door. Next I placed the new gasket around the door frame. Finally, I replaced the screws in the door to completely attach the gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- toney from poplar bluff, MO
- Parts Used:
- 5303207345
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
gasket needed replaced
took off the old one installed the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from Ayden, NC
- Parts Used:
- 216594300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Freezer just quit working. I could turn thermostat off. Click ever few seconds would stop..I figured the thermostat was good compressor not starting
First unplug it and pull away from wall to gain access to the Rear of freezer.
From the rear of the freezer. You can clearly see the compressor.....I had to lay in the floor. Best way to see what your doing .
Attached to the side of the compressor
Is square cover over the start relay..it has a metal bail that retains the cover. Simply remove the strap with a flat blade screwdriver the cover can then be removed. A flashlight and screwdriver is all I needed
The switch body plugs onto the compressor with pins or blades. Mine broke in a few pieces by the time it was completely removed. The start switch has very tight connections so its a bit of a struggle to get it off. ..stick screw driver behind it and try pry evenly until its off..secure new switch on the pins and push it in ..there is one single wire attached to the start switch no confusion there.install cover and its retainer and its done..
From the rear of the freezer. You can clearly see the compressor.....I had to lay in the floor. Best way to see what your doing .
Attached to the side of the compressor
Is square cover over the start relay..it has a metal bail that retains the cover. Simply remove the strap with a flat blade screwdriver the cover can then be removed. A flashlight and screwdriver is all I needed
The switch body plugs onto the compressor with pins or blades. Mine broke in a few pieces by the time it was completely removed. The start switch has very tight connections so its a bit of a struggle to get it off. ..stick screw driver behind it and try pry evenly until its off..secure new switch on the pins and push it in ..there is one single wire attached to the start switch no confusion there.install cover and its retainer and its done..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annie from West Plam Beach, FL
- Parts Used:
- 5303281398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Glass Shelf
1) Remove glass from shipping Container. 2) Using fingers, place glass ever so gingerly in the shelf tray. 3) Pour a glass of wine to celebrate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Albuquerque, NM
- Parts Used:
- 5303281398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problems at all.
Very EASY!! just unpack, wash, and place into slots above crisper doors. A child could do this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- margaret from washington, MA
- Parts Used:
- 5303281398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken glass shelf
The "repair" itself was only a replacement of a glass shelf but I just wanted to say that I ordered this part mid-day wednesday and when I got home from work thursday night it was on my deck, I was shocked. Also it was glass and was very securely packaged Great job parts direct.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from San Francisco, CA
- Parts Used:
- 5303207230, 5303207229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door shelf end cap
simply snap R end cap into R slot in door, then slide one end of retainer bar into R end cap, other end of retainer bar into L end cap, then snap L end cap into L slot in door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kathryn from Buckeye, AZ
- Parts Used:
- 5303281398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I dropped the glass insert while cleaning it and it shattered in a million pieces
I went to the internet to find the replacement glass and shocked at some of the prices....I found PartSelect.com on a blog and the prices were nearly 50% less than the other suppliers. Unfortunately, I ordered the wrong part the first time and had to send it back but after speaking to a Customer Service Rep, I got the right part ordered, recieved it two days later and "voila"....fit perfectly....I so grateful to PartSelect.com for their assistance and the pricing is fabulous..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from Catonsville, MD
- Parts Used:
- 5303281398
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace missing glass shelf
We bought our house and the lower glass shelf in our refrigerator was missing. We lived without the shelf for almost two years figuring it would be a pain to look up the part and replace it on an older fridge. Finding the part and ordering it with PartSelect.com only took me all of 5 mins. If I had known it was going to be that easy.. I would have done it two years ago!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Edgewater, MD
- Parts Used:
- 5303207345
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge door gasket was torn.
Rolled the old gasket to expose the screws for the door panel. Removed all Phillips head screws with a drill and an extension bit. Once you remove the interior door panel dispose of the old gasket and thoroughly clean the surface both front and back of the panel. Install the new gasket and use RTV silicone sealant on the back side of the gasket to ensure that it remains in place. Keep the door closed for as long as possible to ensure that the silicone cures and the gasket remains in place. Hope this helps.
Was this instruction helpful to you?
Thank you for voting!