36360942000 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cathleen from LOS ANGELES, CA
- Parts Used:
- WR72X274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The left side rail had broken where the screws secure it to the delidrawer
The left side rail had broken where the screws secured it to the drawer. Your replacement part fits perfectly! In fact the drawer slides easier now than it did before!
I’d read that I should keep the original screws. They were a bit too big to fit the replacement part. A trip to the hardware store solved the problem and the new slide is now in place.
Your description and drawings for this part really helped me out!
Thank you so much for having this service available for my old but trusty refrigerator!
I’d read that I should keep the original screws. They were a bit too big to fit the replacement part. A trip to the hardware store solved the problem and the new slide is now in place.
Your description and drawings for this part really helped me out!
Thank you so much for having this service available for my old but trusty refrigerator!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from SUGAR LAND, TX
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Switch Not Working - Needed New Switch
Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from EAST JORDAN, MI
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light went out in refrigerator
Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cary from ORLANDO, FL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Ice maker stopped working
Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from DEPEW, NY
- Parts Used:
- WR60X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Broke fan blade cleaning unit
Ordered part came in 3 days. Removed plug and rear cover. Pulled off old fan . Installed new fan by pushing it on to shaft. Plugged unit back in to check operation, installed rear cover. Done. Part fit perfect. Thanks to this site you folks are great !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nan from PURCELLVILLE, VA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My light in the refrigerator was going on and off.
I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marj from NEWBURY PARK, CA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge light dead even with new bulb
1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from BRADLEYVILLE, MO
- Parts Used:
- WR23X37285
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken light switch
This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from EL PASO, TX
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
40 year old refrigerator brittle light switch fell apart
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deb from LIVERPOOL, NY
- Parts Used:
- WR2X8700
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
shelf end cap broke on door
slid it on the end of the shelf and put shelf back on door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from WILLIAMSPORT, PA
- Parts Used:
- WR60X30349
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Evap fan failed, would need restarted by hand when weather warmed up
Repair was super simple. Everything was a direct fit. Hardest part was unloading freezer to access evap motor. My freezer was old making my wire shields very brittle so I cut the shielding and used heat shrink tubing for a neat clean repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Rowe, VA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bulb out
I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lauraine from Rocky Hill, CT
- Parts Used:
- WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
family member melted fan with hair dryer
Unplugged fridge.Removed 2 screws holding a panel. After panel removed took off old fan and inserted new. Quite simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janette from huntingtown, MD
- Parts Used:
- WR17X2769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
needed to replace broken drawer slide rail,
removed produce drawers, removed center piece front cover, removed glass shelf, removed broken drawer slide rail - unscrewing where attached in the rear of the refrigerator. Also removed screw from centerpiece where broken drawer slide rail was attached. reassembled all very quickly....saved myself having to buy another refrigerator by doing this simple repair.
Was this instruction helpful to you?
Thank you for voting!