2539308190 Kenmore Refrigerator - Instructions

Took less than 10 min to install following the inclosed instructions. At first it was not making enough ice to make me happy so I set the temp. a little colder in freezer. Now making ice like crazy. Works better than the old one ever did. Very happy with the new replacement.

I noticed that the two gears weren't meshing together so upon inspection I saw that one of the gears had an inner piece missing making it weak so it kept popping out away from the other great. I ordered the new gear and unscrewed the old one off and put the new one on. So easy. It made Ice beautiful after that

Very EASY!! just unpack, wash, and place into slots above crisper doors. A child could do this.

Tested for power and found the thermal cut-off bad. Installed new one.

moved freezer items to right of icemaker,loosen two nuts lifted icemaker over nuts,squeezed and pulled cable out turned over marked L bracket screw with marker for location plugged cable in tighten screws,made ice in 2 1/2 hours john

Unplug refrigerator power cord. Remove ice cube bin. Place wire signal arm in down (off) position. Ice Maker is held in place by two (slotted/hex headed) screws through keyhole slots over the top of Ice maker along the left side of freezer. Use mirror to locate screws then carefully loosen (do not remove) screws with a nut driver or screw driver. Lift Ice maker up and right until it releases from the screw heads. Unplug electrical connection. A flat screw driver may be required to loosen connector. Connect new unit electrical and Install new unit over screw heads and tighten screws. Replace Ice Bin and place wire signal arm in the up (on) position. Reconnect refrigerator power cord. After freezer cools down sufficiently it will start making ice.

The "repair" itself was only a replacement of a glass shelf but I just wanted to say that I ordered this part mid-day wednesday and when I got home from work thursday night it was on my deck, I was shocked. Also it was glass and was very securely packaged Great job parts direct.

simply snap R end cap into R slot in door, then slide one end of retainer bar into R end cap, other end of retainer bar into L end cap, then snap L end cap into L slot in door.

1) Remove glass from shipping Container. 2) Using fingers, place glass ever so gingerly in the shelf tray. 3) Pour a glass of wine to celebrate.

The gasket was held to the door by the door's interior plastic shelves. Remove the 12 screws holding the interior mold to the door and the gasket comes off too. Then it is just a matter of fitting the new gasket around the mold and then screwing the mold back onto the door.

Rolled the old gasket to expose the screws for the door panel. Removed all Phillips head screws with a drill and an extension bit. Once you remove the interior door panel dispose of the old gasket and thoroughly clean the surface both front and back of the panel. Install the new gasket and use RTV silicone sealant on the back side of the gasket to ensure that it remains in place. Keep the door closed for as long as possible to ensure that the silicone cures and the gasket remains in place. Hope this helps.

The two screws that held the ice maker in place could not be seen do to there location. I could only get one hand inside do to space restriction.So I placed a mirror inside so I could see the screw heads and from point it was very easy to see and line up the nut driver on the screw heads. I then lifted it up and unplugged the wiring and installed the new ice maker. Works like a charm. Paul

I am a 65 year old woman with no mechanical aptitude: I just unplugged the frig. And used a screw driver to pry of the plastic socket from its outside edge. . Then you just unplug two tiny contact plugs that appear when you pull out the socket and replug in those two the same way on the new part. Pop the socket back into the hole . . . . And screw in the new bulb. I knew I needed the socket part cause when the bulb burned out , a new bulb still did not work. . . If I can do it, anyone can!

Went well overall. I really thought that you guys taking the time to create a very helpful video was awesome. Thanks for doing that! The only difficulty I had was that my old ice maker had the connection toward the front, while the new one was in the back. So I had to use the adapter and had so much extra wiring to bundle, and tie wrap, with little place to go with it that I got frustrated. Wish I just had the correct replacement wire to begin with. Nonetheless, we are stocked with a full bin of ice after about 3-4 days.

loosened two 1/4 in. screws removed ice maker unplugged harness. Plugged back in slid the replacement ice maker over the two screws secured. Done