25338652990 Kenmore Refrigerator - Instructions

At top of refrigerator compartment, took out screws to cover (where temp control is) and to the right took out 2 screws to remove defrost timer and installed in reverse order. In freezer compartment, unscrewed back of freezer wall and took off completely. Removed old freezer thermostat, the body of freezer thermostat snapped onto coil and wire plugged in. Let run for 24 hrs, then made adjustments to temps, so far temps are back in normal range.

The fan motor all but caught the inside of the freezer on fire . Had to remove then clean, and I mean clean the walls of the freezer . Then had to pry out the old fan without breaking anything . Replacement of new fan was quick and easy because all the parts that I needed were in the bag

I had already removed the ice maker by loosening the two screws with a 1/4" nut driver, in order to compare the design and style to the intended replacement for size and critical measurements. The replacement was almost identical. The wiring harness was 2-3" longer than the original, but after snaping the wire plugs together I simply curved the wire up and to the left to be out of the way. The hanging brackets are slotted and it was easiest to slip the back hanger over the head of the screw and let it slip down, then the front hanger was already to line up even though you can't see the screw with the ice maker in the way. I had to transfer an L-shaped metal bracket to the bottom side, matching the old assembly, and adjusting it to hold the bottom side away from the freezer compartment a little so it would hang level and secure. You have to snug the two screws with a screw driver or 1/4" nut driver by feel, since you can't see them with the icemaker in place. It took about 10 minutes to take out the old and another 10 to put in the new. We now have a full bin of ice, and the old plastic trays have been retired. I should have done this a year ago.

Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror

First, unplug the refrigerator since you're working with live wires.

Remove the 4 Philips sheet metal screws holding the plastic housing that holds the temperature control to the top of the refrigerator compartment. Pull the housing down then out since there is a tube on the housing where the water flows out the back of the refrigerator during the defrost cycle.

Remove the 2 Philips screws holding the defrost timer on the plastic housing. Pull the connectors off the old timer and attach them in exactly the same positions on the new defrost timer.

Attach the new defrost timer to the plastic housing with the 2 screws.

Reinstall the plastic housing, making sure the water tube is inserted into the back of the refrigerator wall.

Plug the refrigerator back in and you're done.

remove all freezer items and remove back panel covering the coils - about 8-10 nuts using a nut driver. The coils in my refridgerator were covered with a heavy frost - thermostat was also frozen over. Manually turn the defrost timer so the fan turns off to observe if the heating element is working (defrost timer is on the bottom front of the refrigerator on the left side). My heating element did work so I decided to replace the thermostat and defrost timer. Unplug the refrigerator. Disconnect 2 wires connecting the thermostat and unhook. Replacing with new thermostat - red and white wires that have male/female connectors and hook onto coil as before. Note that two parts with similar names were offered by PartsSelect and you really couldn't tell which was the right one - I got both but returning the unused one was very easy but cost a couple of bucks in shipping. Next, take out two screws and the bracket that holds the defrost timer in place and unplug it. Plug in the new one and screw it back in. Reinstall the back panel - throw out all that stuff in the freezer that you've had in there for 10 years and turn it back on - very simple and it worked perfectly. Very good experience with returning parts - excellent customer service.

Used exploded parts view to locate part. Removed old part and replaced with new defrost timer. Piece of cake.

You have to blindly unscrew the two screws along the side of the ice maker. Once that is done simply remove the ice maker to the side to gain access to the electrical plug. Undo the plug and remove the ice maker completely. Install the adapter on the new ice maker and install it in much the same way you removed the old. I started the (2) 1/4" screws before installing the new ice maker to make it easier to hang. Pay careful attention to the wire harness and dress it out of the way. Finally tighten the two screws and make sure the bail wire is down to begin ice making once again.

I took a look at the web site where I purchased the parts, then I took a look at the paper enclosed with the order. Thankfully, I have a battery operated screw driver since there are so many screws. There are plenty of screws in my refrigerator and freezer doors. I thought that since my old door gaskets were all chewed up looking, if I changed them, the 10 year old air conditioners and the old fashioned light bulbs to instant on energy saver light bulbs, the electric bill would become more manageable.

The refrigerator and freezer door gaskets were the first step. They were easy to swap out. You just need to empty the door of all food items, then pull back the old gasket to see the screws. There are alot of them. You should leave 2 loosened screws on each side of the refrigerator door to hold the panel in place while you work and remove the rest. Then you can remove the old gasket and slide the new one into place. Make sure as you tighten the screws and replace the ones you removed, the new gasket fits into the door panel groove securely and is in place as you tighen the screws. Make sure it is in place all the way around the door as you work. You repeat the procedure for the freezer using only one loosened screw on each side to keep the interior panel in place while you work. It takes some time due to the number of screws, but the work is pretty easy. I never even broke a nail.

The end caps for the shelf bars just snap into place just as the old ones can be snapped out with a bit of pressure. They do not have to be wrestled and you need to work carefully so that you do not break them. (I ordered an extra just in case, but I didn't need it. I will have it in case I need it in the future)

My electric bill dropped from $450 to $110 a month with all the improvements I made. Thank you Part Select for taking the fear of screwing it up, out of the repair process and making it manageable. I can afford my electric bill now. Thanks for your help.

Shut off water/power - pulled tray -loosened two screws holding ice maker - lifted it up and off - unhooked power connection installed new maker in reverse of above - power supply line was much to long but just pushed it under the ice tray ( away from the maker ) prior to ordering looked at comments from others regarding installation

I want to first say that before I ordered this part from "Part Select" I first went and talked with a local appliance repair shop. They quoted me a $120 charge to come out and check the problem. Then $30 and hour service fee, plus parts. He provided me a quote of about $250 for the job.
I found this part easily on the web site $77. It was very easy to instal. The only problem I had was the fact that in the side by side it was very difficult for me to get two hands inside the freezer to install it. (I have wide shoulders). Two screws loosened, no need to remove them. Just life the entire unit straight up. Unplug wire harness. Then just reverse order. Could not be easier. If you can change a light bulb you can do this.

I purchased the replacement part (no instructions sheet) from another company, not this one, that cost 2X's a much as this company. So I sent it back and ordered from this company. Got it faster then the post office sends us the stamps we order by internet and this ice maker had instructions.
Our's is a side by side refrig, so working space is limited but do-able. The old ice maker has made a clicking noise for years while trying to push the cubes out of the tray. They would get stuck and refreeze, sticking half way out of the tray.
I loosened the 2 screws with a socket driver (which are difficult to see), raised the unit up and off the screws. Unplugged the power & out it came. Removed the bracket on the side as instructed to attach to the new ice maker and in the trash the ol' ice maker went. Set the new ice maker on the screws, plugged in the power, tightened the screws and walla. A quiet ice maker. In fact, it would startle us the first day as we didn't hear the clicking noise indicating it was stuck. All of a sudden the cubes just dropped into the container. Alright! Don't know why I didn't do this years ago.

Bought a new
capacitor.

There are 3 parts that actually control cooling cycle: Temperature Thermostat, Defrost Timer and sensor/relay on the back side of the appliance. If fridge cycles up after you turn small knob on defrost time (you'll hear click, problem lies between first two components.
Replacing them is really easy. Make sure you handle thermostat wire carefully. Check for connectors holding firm.
Use schematic diagrams you may find at this site.

Good luck.

Removing the old unit was easy enough, just loosened two screws that attach unit to side of freezer and disconnected the wiring harness. But the new unit never goes in quite as easily because it's always just a little different from the original. In this case, the wiring ended up being about six inches longer and the excess had to be stuffed behind a shield at the rear of the unit. Theoretically, the wire could have been pushed back through the opening, but it got jammed and wouldn't go. I had to remove side rails and pry the shield forward in order to get the wiring back out of the way. The unit is a narrow side by side, so there wasn't a lot of room to move around. But it wasn't difficult, just tedious. I had to make sure the wiring did not come into contact with the heating element at the bottom of the icemaker. Once installed it worked great.