2539343000 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nancy from Schenectady, NY
- Parts Used:
- 3206150
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no shelves refrigerator door
Needed to saw the pieces. PUrchased hacksaw.
Son sawed the pieces. Went in like a piece of cake.
Son sawed the pieces. Went in like a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from WHITMORE LAKE, MI
- Parts Used:
- 5303324302, 3206166, 3206165, 3206150
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old end caps were broken
Pulled the few end caps off the retainer bars, pushed the new ones in, and used a medium hand strike to seat the end caps in the doors slots.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- earl a from GIRDLER, KY
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light blub blew
unplug power from ref removed old light socket only difference wired a little different checked new socket compaired to old checked terminal ends small big looked at wires big,little plugged up put in new light blub plugged ref power back on work power off pushed socket bac in power on works
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIM from WOODBURY, TN
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The refrigerator light would not work ...even after replacing the bulb.
I used a flat head screwdriver to pry open the front of the socket as I pushed the socket toward the freezer side. I unplugged the two wires connected to the socket then re-connected the two wires to the new socket and popped the new socket back in. I then put a new light bulb in and we had light again in the fridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Kearny, NJ
- Parts Used:
- 5303324302, 3206150, 215366002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my refrigator did not have the lower door shelf retainer bar
the repair went fast and easy. my boyfried measured the retainer bar, cut it with the hack saw installed the right and left side door shelf end cap and inserted the door shelf retain bar. the door looks great. would highly recommend your website and customer service. thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Grants, NM
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defrost timer was not working
Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Lonaconing, MD
- Parts Used:
- 218724000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
front roller assembly was missing/holes stripped
Unplug fridge, tilt back against wall to provice clearance to install new assembly. Used self starting screws to install. Used cordless drill with nutdriver to install assembly.
Time to complete job-5 minutes
Time to complete job-5 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geoff from Farmington, NM
- Parts Used:
- 5303324302, 3206150, 215366002
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door shelf retainer bar was missing from fridge door
The replacement part was a bit too long (about 6"). Measured length of the existing bar that was on lower shelf and used a rotary tool with a metal cutting disc to make the same length. Everything snapped into place easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Bay City, MI
- Parts Used:
- 5304464438
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Fridge quit working.
A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Spokane, WA
- Parts Used:
- 5303917954, 215846602
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Temperature in both freezer and fridge sections to warm!
Dear Part-select,
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Tom Houck
Spokane, WA
Houck Photo
509-723-3418
tomhouck1@comcast.net
I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 part if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Tom Houck
Spokane, WA
Houck Photo
509-723-3418
tomhouck1@comcast.net
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Sunnyvale, CA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No freezing or cold in either freezer or refridgerator - compressor did not run.
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roland from Stoneham, MA
- Parts Used:
- 5303001015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Handle and End were missing
After first ordering the wrong end part, I reordered the correct part and successfully attached the handle end and handle to the refrigerator door. The handle itself was too long, and I had to cut it down to the correct size. I am a realtor and provided the service to my buyer of the condo that was my listing. Thank goodness for your company and the ability to buy parts for an old model!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Eatonville, WA
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defroster didn't work
Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE
Cool.
GWE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Connie from Seneca, SC
- Parts Used:
- 5303324302, 3206150
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end cap broke
First I removed the broken end caps. I placed the new end cap onto the shelf bar and snapped the end cap into the holding slot on the door interior. Took about 5 minutes. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Springfield Gardens, NY
- Parts Used:
- 5303324302, 3206150
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom shelf (beverage shelf, large bottles, etc.) was unuseable because the plastic end caps were cracked. The metal shelf bar was intact though.
We have a wonderful Kelvinator refrigerator. It has served us tirelessly for more than 15 years - and looks as good as new! (We frequently clean it out and clean the interior and exterior, to keep it looking and smelling clean)
Replacement of the end caps and shelf was very easy!
The broken end caps were removed (missing for years), and it became one of those small projects that one never gets around to. I finally took down the model number and looked online for it. Google or Yahoo (can't remember which) pointed us to you site. I was SHOCKED to see that the parts were still available! I called your friendly customer order line and had a very pleasant experience placing the order. The BIGGEST shock came when the parts arrived THE NEXT DAY!! Just in time for Thanksgiving! You are AWESOME!
The Repair:
Easy as pie. The end caps simply snap into place. I did the left side first, then carefully inserted the metal bar, which is supported by the two end caps. Next I snapped in the right side cap - DONE. It took longer to clean the bar up, than it did to replace the caps!
The Results:
The bottom door shelf is now useable again. We can place 2 liter beverages and juice containers on the door, where they belong! My wife cheered and commented, "The refrigerator is no longer an eye sore when I open it!" :-)
Thank you Parts Select!!!!
Replacement of the end caps and shelf was very easy!
The broken end caps were removed (missing for years), and it became one of those small projects that one never gets around to. I finally took down the model number and looked online for it. Google or Yahoo (can't remember which) pointed us to you site. I was SHOCKED to see that the parts were still available! I called your friendly customer order line and had a very pleasant experience placing the order. The BIGGEST shock came when the parts arrived THE NEXT DAY!! Just in time for Thanksgiving! You are AWESOME!
The Repair:
Easy as pie. The end caps simply snap into place. I did the left side first, then carefully inserted the metal bar, which is supported by the two end caps. Next I snapped in the right side cap - DONE. It took longer to clean the bar up, than it did to replace the caps!
The Results:
The bottom door shelf is now useable again. We can place 2 liter beverages and juice containers on the door, where they belong! My wife cheered and commented, "The refrigerator is no longer an eye sore when I open it!" :-)
Thank you Parts Select!!!!
Was this instruction helpful to you?
Thank you for voting!