3638795998 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mitchell from Chicago, IL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The Ice Maker stopped making Ice because the arm over the ice bucket which turned turned on the icemaker was broken
I read the step by step instructions that came with the part. I turned two screws and disconnected the electrical harness and Removed the icemaker. Two other parts from the old icemaker were easily removed without any tools and put on the new icemaker. The new icemaker was put in the same way the old one came out. I reconnected the electrical harness and tightened the old screws. The hardest part of the whole job was reading the directions. They were easy to follow if you take the time to Just read them!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Reading, MA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No ice.
Piece of cake and now I get loads of ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from San Antonio, FL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice maker not working
unscrew one screw unplug.insert the ice maker,put the screw back in you have ice less than ten minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert jr from east rutherford, NJ
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Frig was not making ice.
Removed the faulty ice maker in about two min.. New unit was installed in approx. five min. Watched your video prior to installation and it helped greatly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Norwood, NC
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
No problems.
Took out the old, replaced with the new. Needed second person to hold the flash light. That is the secret to get it plugged in and secured.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Edmond, OK
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice Maker stopped making ice.
Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from JASPER, GA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Was not making ice cubes
Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurie from Portland, ME
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cord
The adapter made the cord a bit long but other than that it was great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dickei from Sugar Land, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker quit makeing ice
Wathched the video and it was done in less than 15 min making ice again no problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from Coralville, IA
- Parts Used:
- WR30X10093, WR29X5153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gears were jammed, and broken when jam was cleared causing them to make loud knocking noises when spinning
Popped off the old gears with a screw driver. Put on the new gears with a screwdriver. Problem fixed in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!