3639512413 Kenmore Refrigerator - Instructions

Removed the old, screwed in the new. Very easy, thanks for the video.

I glued the old rail back together twice prior to resorting to ordering the the replacement drawer rail from parts direct. Don't bother glueing the old parts, just buy a new one. Keep the screws from the old drawer rail as new screws are not shipped with the replacement rail. Only took 10 minutes to replace the rail needing only a phillips screwdriver. Good as new.

- Remove drawer and cover being supported by this slide. - Remove front and back screws with the screw driver. - Replace the above removed screws using the new slide. - Replace drawer and cover. DONE

Remove glass shelf. Remove slide (2 screws). Replace with new slide. Replace glass shelf. Done.

Remove broken rail by unscrewing two phillips screws
Discard broken rail
Hold replacement rail in place with left hand, tighten phillips screws with standard phillips screwdriver.
Wash scratch marks off bottom of fridge caused by drawer sliding on bottom of appliance
Slide veggie drawer into place, smile at wife, receive praise.

Piece of cake, unscrewed two screws on each drawer guide and simply relaced the new sides. Fit was perfect and fridge is like new again.

Remove drawers and shelves. Remove and save the 2 screws holding each old rail. Replace new rails using old screws. Replace shelves and drawers.

Be careful: PartSelect lists several different rails for the same number in the parts diagram. Make sure the rail you buy matches the one you're replacing.

Removed 2 screws to remove broken slide, replaced 2 screws with new slide. Took every bit of 4 min. to complete job.

I removed the top shelf and removed broken rail and instaled new rail only two screws .

I removed the screws holding the remaining portion of the slide rail in place. I was able to install the new rail by simply attaching the part to the fridge using the same screws. Having an electric screwdriver made the job very easy.

After fixing my washer this was a snap. After lifting out drawer and shelf only two screws needed removal. I think it was easier putting it back together! It is sites like these that make it possible for men to feel like men!

This one is a no brainer… One Phillips screw on top to pull top door hinge trim. Two nuts and the top hinge is free. Then pull the door… it helps if you unload all the crap in the door bins. Remove the remnants of the door cam and that leaves a pop rivet. Put some vise grips on the head and use a hacksaw to remove the lower part of the rivet. Then pop-rivet the new door cam in place. If you don’t own a pop-rivet tool, I guess you could use a 10/32” screw and nylock. Plop the door back on and you’re done. Took all of about 15 minutes.

I unscrewed the broken slide rail and screwed in the new one. Voila!

First i removed two screws that holds the ice maker in, unplug the plug to the ice maker. I was able to remove the old one. Place the new one in screwed in the two screws and pluged in the plug and in just a little while i had ice again. I am a women, if i can do it any one can. I had a repair man tell me it was going to be $250.00 dollars to replace it. I got on line ordered the ice maker and had it in 4 days. Very fast shipping and easy to install. Tina Kearns Beaumont, Calif

Look at various pertenant DYI articles and videos on the internet. Replaced water filter with bypass plug. Checked water flow to icemaker water solenoid. Ran icemaker diagnostic test which failed. Ordered replacement. On receipt of replacement, began replacement work. To wit: Pulled fiidge from wall and unplugged. (Not necessary to shut water off.) Removed small freezer basket. Unloaded main freezer basket, removed it then removed the freezer door. (A screw on each side bolts the door rail of the chassis slide to the freezer chassis slide.) Loosened screws on rear, top of partition between icemaker and small freezer basket. Pushed up on partition front and popped out U-bar supporting partition bottom being carefull not to bend it. Removed same. Removed screws from partition and set aside. Removed grilled "thingy" between rear of icemaker and partition. Now have access to icemaker screws. Loosened the screws, pushed up and out and carefully let it hang by it's connector. Fiddled with the connector locking tabs and finally got it loose. Compared old and new icemaker. Have to keep the old water funnel. The new wiring harness was stiff and the connector had a different orientation. Twisted both the wiring harness and connector to align connector while the icemaker hung by it's cable being careful not to let the icemaer slip and fall to the bottom. After much fiddling, got the connector inserted and locked. Set icemaker over the two screws, pulled it down and tightend the screws. Put the old funnel into the new unit being very careful to get it right the first time. Put grilled "thingy and the partition and U-bar back in, put door back on, put the ice cube bin back, freezer drawers bac and reloaded the frozen food, plugged fridge in. Done! Time to replace icemaker was about 20 minutes and another 2 hours to do the rest ofthe work. Still required only a nutdriver and phillips.