3639711510 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Patricia from Norwood, NC
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
No problems.
Took out the old, replaced with the new. Needed second person to hold the flash light. That is the secret to get it plugged in and secured.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Edmond, OK
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Ice Maker stopped making ice.
Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from JASPER, GA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Was not making ice cubes
Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Las Cruces, NM
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
no ice
Followed the video, very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from clinton, TN
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
would not make ice
i watched the free video and then made the switch my ice screw had 4 bolts instead of three that was the only difference used the screw driver to loosen the straps on the connection plug and that was it easy as pie in about 30 minutes i heard it drop a load of ice it beats filling ice trays all the time thank you partselect for the free video it was the difference in my sucess
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Santa Fe, NM
- Parts Used:
- WR29X5171
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Ice maker kept on making ice
I ordered a new micro switch that was activated by the high ice lever. Once the switch was replaced the ice maker cut off as it should have and stopped producing too much ice. YHis job was of moderate skill level, the most challenging was replacing a spring that popped out then reassembling the unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colleen from Yorba linda, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Was not making ice
Took old part out , put new part in. Was so easy thought we did it wrong. Ice maker working great, have lots of ice now. Thank you. Colleen
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dickei from Sugar Land, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker quit makeing ice
Wathched the video and it was done in less than 15 min making ice again no problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from Coralville, IA
- Parts Used:
- WR30X10093, WR29X5153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gears were jammed, and broken when jam was cleared causing them to make loud knocking noises when spinning
Popped off the old gears with a screw driver. Put on the new gears with a screwdriver. Problem fixed in less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from San Tan Valley, AZ
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice Maker stopped working
Took out one hex screw, disconnect electric couplings, pulled original ice maker out and found that the water supply line to the ice maker was frozen solid as well as the shute cup. Used hair dryer to thaw out the line and the cup reinstaled old ice maker and it worked fine. Did not have to use the new part at all at this time. Am keeping new part for future use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy H from Leesburg, VA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
iCE MAKER LEAKING WATER
Followed the video demo and would have been done sooner but for limited work space- narrow freezer compartment and the release tabs on the electrical plug. First home repair that the air was not blue and got done in under time allocated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from North Billerica, MA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Icemaker stopped making ice
I just followed the directions carefully, loosened the screws with a nutdriver removed the unit from the screws, unplugged the unit from the freezer plug, took out the new unit, used the adapter supplied with the unit to match up with the plug in the freezer, carefully attached the icemaking unit to the screws, carefully slid the cord behind the unit, lightly clinched down the screws, checked it with a level and then did the final snug down. turned the unit on and it worked fine. Pretty easy, just take your time, don't rush and it will come out fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eduardo from Arlington, VA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No Ice...
Super easy, had my 15 year old do it (with my supervision).
Followed very clear Instructions that come with the replacement...
But, he could not get to the plug location until he removed 4 screws holding the motor assembly that spins the ice in the drawer and moved it out of the way...
Followed the rest of the instructions...
Works like a charm.
Followed very clear Instructions that come with the replacement...
But, he could not get to the plug location until he removed 4 screws holding the motor assembly that spins the ice in the drawer and moved it out of the way...
Followed the rest of the instructions...
Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Wildomar, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old Icemaker Stopped Making Ice
Instructions that came with the part were useless. I would have created new problems if I had attempted to follow the instructions. However, once I had the old part removed and put it beside the new part, required repair process was obvious, easy and quick. Frig now makes ice better than it ever did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Pampa, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker was leaking
Watched the video that showed how to disassemble the ice maker. Then went right in and replaced the part and turned it on. It immediately started filling up the ice tray. I still have not been able to find out why it does not make as fast as the original ice maker. The tempeature for the freezer is set pretty cold.
Was this instruction helpful to you?
Thank you for voting!