10670234902 Kenmore Refrigerator - Instructions

I just slipped the new drawer into place. So easy, even a woman can do it! ( I am female!)

Thought The issue was the solenoid valve. Took a lot of research but finally found through parts select. Perfect match and easy to install, but unfortuantely, it did not solve the problem of poor ice production. Now would appear that the icemaker itself needs to be replaced.

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

Removal of the door gasket went quite fast. First i needed a 8mm wrench. That what I didn't have. Got the socket set, not the wrench. Tried adjustable wrench, went slow. I slowly got the bolts out. Putting the gasket on was slow. Then I get to the last corner, was awful for me. I finally get it on. Putting the freezer door back on 1st went crazy. I finally looked on top of refrigerator, saw (3) bolts, removed them, installment went easy from there.

I took the cover off, and noticed the tabs holding the timer wheel were broken off on one side. after removing the wheel, I noticed the shaft from the ice lifters was broken. Since the only way I could repair it was to buy the entire module, which I did. I received my part in 3 days. When it came, I began removing the old module by taking out the three screws holding it. After replacing the module which took about 10 minutes, my machine was making ice within about an hour. My ice holder was full in 3 days. Albert Moran, Milton, Fl

Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.

I ordered a new one waited for the new ones to come in once it did I took out the old ones and replaced them with the new ones. It was simple.

The bar slipped right into a groove on each side and took less than 5 seconds.

Valve-inlt had stopped functioning. The longest part of the repair was determining that the water lines weren't clogged and were working efficiently. Replacing the faulty valve only took a matter of minutes. The part was ordered and shipped in a timely fashion. Thanks!

Removed old ejector arm and installed new part.

Removed door and replaced bushing bracket was ok.

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

I attached the hinge and secured it with screws and socket wrench.

inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."

I'm so glad you asked! You sent a SUBSTITUTED part which came nowhere near fitting the refrigerator. You have, so far, ignored three emails in which I requested a refund for the part as well as the shipping both ways. Since you sent something I didn't order, and it didn't do the job, that seems only fair. Evidently you guys don't agree. I don't have any problem with the fact that you probably sent something you THOUGHT would work - my problem is that you seem to feel that it's my mistake, so shipping costs ought to be on me. I will continue trying to get this issue resolved, but I really hope you do print this on your website. I'm not certain why you have a customer service address when no customer service exists. I am very disappointed with this whole transaction.