10670234902 Kenmore Refrigerator - Instructions

took out broken with no tools req replaced new with no tools req

Too simple! I removed the crisper bins, took off the broken crisper cover and replaced with new crisper cover then inserted the bins under it. Viola! Ordering a part from this site was so easy. My frig is 10 years old and I didn't think I would be able to find a part, but it did.

I just removed the old seal cleaned the area and simply installed the new seal. The instructions were easy to follow and project was completed in less than 1 hour.

First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.

This must have saved me $300, and the inconvernience of waiting around for the repair man. He would have made two trips since he would never have had this part with him.

This would have been a less-than-5-minute repair except for one item. The water intake nossle was 180 degrees from the original part. As a result, the copper water inlet tube would not fit in the old space and still allow me to reattach the valve to the freezer chassie. I ended up leaving the valve hanging loose under the freezer. I spent most of my time trying to fit the valve into the old space.

Unplug freezer. Disconnect electrical connections (pull apart). Remove one screw holding the valve to the chassie. disconnect water inlet pipe and water outlet pipe from old valve.

Reconnect electrical connection to new valve. Reconnect in and out water hoses. Reconnect valve to chassie. Plug freezer back in. Finished

Everything works just fine !

While cleaning the refrigerator I had taken the bottom glass shelf out to clean it in my sink and unfortunately it broke into thousands of little pieces. After clean up the mess and my cut thumb, I went online to see about replacing it. First went to Whirlpool site, they had the broken shelf but for considerably more than I found on your site. Your website was easy to use and the part and the shipping was much more reasonable. I ordered on a Sat afternoon and the shelf, which was exactly the same as the one that had broken, was on my front porch by Tues @ 9:00 am. You never know when you make a purchase online with a company you are not familiar with, but I can say this was a great experience.

Quoted $275 to fix, paid $65 for the part , Installed the new part in about 15 min. very easy, removed 2 small screws, and plugged in new part.

!st removed the doors from the unit, then laid them on the floor. Next, on a long side of the door, cut through the gasket so I could pull it off the door in one piece without separating the door liner from the outer door. Then, starting at a corner, started pushing the stiff black part of the replacement gasket between the liner and outer door, making sure to push it completely under as I went. Used a thick flat bladed screwdriver to carefully help push the final corner section in. Repeated on both doors, rehung, plugged in and done!

Unplugged the machine removed the bottom plate and back plate and ice maker.Removed 2 wires to motor and ground wire.Removed 2 mounting nuts for motor,installed new motor and used old fan blade for new motor .Reinstalled in reverse order plugged in and tested fine.

Snap on bracket snapped off easily with minimum force. Removed the existing bent and broken sheet metal trim piece. Inserted new piece into one side of bracket, then the one in hand, then snapped into place.

plastic warped in ,spaced out and, the socket snapped back in place.

Take bottom racks and baskets out of freezer. Remove back sheet metal panel, 8 screws. Remove motor and bracket, 2 screws. Umplug wires on motor. Remove two more screws to take mounting bracket off motor. Install in reverse order. Simple job. Maybe 20 minutes. Besure to shut freezer off before startin work.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Replaced with new parts

Contacted sears home service to perform repair. Quote for repair was $307. 43. ( $196. 90 For labor ,$102. 58 For part) plus $75. 00 For service call. Based on the charge, I refused the repair and ordered the appropriate part from "part select" (733947) (wpl 8201515) motor module for a cost of $81. 84. To my surprise, the part arrived the next day and in 15 minutes the icemaker was in a position to make ice, and has been producing ice ever since. To perform the module replacement, I had to remove one screw with a nutdriver, pull the icemaker out, disconnect a wire harness, replace the module and do the reverse procedure to complete the installation. I saved a total of $225. 59 By doing this repair myself. A lesson learned. . . . . I will always investigate doing a repair myself with the help from the people at part select. Very professional and they sent the correct part the first time.