59678333802 Kenmore Refrigerator - Instructions

Googled "intermittent clicking noise" or something similar and consensus was it was either the capacitor or compressor start relay. You-tubed videos on how to replace these. Looked easy. Just unplug them from the condenser and replace. Contacted Part Select and staff said 50% of the the time it was the capacitor, 50% of the time it was the relay. I was in a time crunch so I ordered both and they came in a couple of days. I replaced the capacitor but the clicking noise continued. I replaced the relay and problem solved! Maybe I could have gotten away with just replacing the relay, but I had them both by then and figured with a 10 year old fridge, better replace them both at the same time and be done with the problem. So far, so good.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Replaced water/ice maker inlet valve from video instructions from Just Answer. The inlet tube for the water dispenser would not cede in the valve and this created a leak problem from the water dispenser connection. Called repair tech and he could not get the line to cede correctly in the inlet valve. Am going to request a replacement part. This has been very frustrating!

Let the ice in the freezer melt while installing P trap drain tube

Followed the video on the web site and proceeded in a slow to moderate speed. Didn't rush the job. It went smoothly

Prior to ordering I removed freezer panel and checked for ice build up and fan functionality. Then removed rear panel cleaned lint from everything pulled front panel vacuumed out the condenser. Plugged back in and all seems to work with the exception of compressor. I have a little experience so googled in model number and your site popped up. I looked up part and the site gave me a percentage loved that. I ordered wish I would have rushed shipping as took about 10 days. Installed in less than 30 minutes and all runs great ??

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

Looked online for instructions. I had to remove the shelves from inside the frig, then pop off part of the right inside back wall. The way the 3 water lines attached to the inlet valve was a terrible design. There are plastic little collars that need to be pushed back to release the water lines from the old valve, then when you install the new valve, you need to push them back to reattach the water lines. Once installed, one had a leak. No matter how hard I tried I couldn't get the little plastic collar to disengage. I couldn't push the line in further and I couldn't get it back out. Ended up cutting the line off at the valve just to get it out. Then had to cut out the piece that was still stuck in the valve. Tried to install it again and it leaked even more. Ended up putting the old valve back in and throwing away the $130 new inlet valve because there are no returns on electrical parts. Total waste of time and money ! ! ! Not happy to say the least.

I easily ordered the part. When it came in, I just shut off the water, disconnected the electricity, and followed instructions to remove shelving and drawers. Then removed the rear interior cover, removed the old water inlet valve and installed the new one. Just a couple moldex wire connections and the 3 water lines in and out. Don't know if this is still ok, but so simple a caveman could do it. Sorry Geico.

first of all,i just want to thank parts select for sending me a second ice maker at no charge.after installing the first one and it didn't work,i talked with Heather and she sent me a new one.installation went the same as before.hardest part is getting the quick connect wire harness apart and the ice fill arm .it is working great and my home is happy.thank you!

Very easily removed top shel glass above crisper--removed old rail by lifting up--and place new one in slots provided---simple!! Part was delivered in less than 3 days-------very fast and cheap !!!

Saw U tube instrctions how to install and it was easy

Total time 10 minutes. 9 minutes to clear out the food and 1 minute to install the part. Installation was self evident and could have been done blindfolded. Part just snapped in.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.