59668942800 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Julie from KIRKERSVILLE, OH
- Parts Used:
- WP67006531
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
No water getting to Ice Maker
Cleaned all lines running to water control valve and ice maker. Replaced water control valve still no water to Ice Maker. Replaced Ice Maker as tec. support suggested. Still no water to Ice Maker talked again to tec. support they didn't know what to do? After I spent 200.00 dollars in parts and shipping. NOW I still have get a repairman out fix the problem. The program is helpful but I don't see why you don't have someone to talk to about the problem that knows what they are talking about. It may be a defective waters inlet valve that you sent. The Ice maker does work if it had water. I ran a test with the jumper wire as suggested.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from ZUNI, NM
- Parts Used:
- W10613606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Refrigerator went out during blackout.
Installed the part, fan turned on, lights on, however, the freezer did not get cold and refrigerator is not working at all. Need advice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor R. from BROOKLYN, NY
- Parts Used:
- WP67006531
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Stead flow of water from under the refrigerator
Unplugged and disconnected the water supply.Disconnected the water line coming from the filter and cut about 1/8 inch off to square it off.
Unscrewed panel to expose inlet valve. With a marker I noted where the lines need to go back to. Disconnected the other two lines and made fresh straight cuts with a utility knife. Disconnected both plugs from the old inlet. The yellow one was difficult to get off, so I carefuly used a screw driver. Be careful, you don't want to break the plug. Reinstalled the new inlet. make sure that you push all of the lines in the valve so that they are completely seated. Make electrical connections. Secure valve to the panel. The water line from the filter should be the last line that you connect. Put screws back in the panel.
Plug in and turn on water supply. Fill up a gallon container from water dispenser. Check for leaks. Let the ice machine fill up. Check for leaks. Place back panel back on and secure. GOOD LUCK!
Unscrewed panel to expose inlet valve. With a marker I noted where the lines need to go back to. Disconnected the other two lines and made fresh straight cuts with a utility knife. Disconnected both plugs from the old inlet. The yellow one was difficult to get off, so I carefuly used a screw driver. Be careful, you don't want to break the plug. Reinstalled the new inlet. make sure that you push all of the lines in the valve so that they are completely seated. Make electrical connections. Secure valve to the panel. The water line from the filter should be the last line that you connect. Put screws back in the panel.
Plug in and turn on water supply. Fill up a gallon container from water dispenser. Check for leaks. Let the ice machine fill up. Check for leaks. Place back panel back on and secure. GOOD LUCK!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from LOUDON, TN
- Parts Used:
- WP67006877
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
broken glass shelf
Replaced shelf, very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from HUNTINGTN BCH, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Difficulty removing old switch.
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from AUBURN, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from SAINT ALBANS, VT
- Parts Used:
- WPA3223101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Water line feeding ice maker was not producing ice
Take out the elbow fill tube and check to see if ice build up inside tube. Clean tube of ice build up. Replace tube back in. In my case that corrected my problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlton from CHICAGO, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light out.
Popped out the old switch and replaced it with the one dying
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from Westford, MA
- Parts Used:
- WP67001255
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed a larger ice pan for the freezer.
I took out the old one and put in the new one. For some reason the repair story associated with the ice bucket had nothing to do with ice buckets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary L. from Millsboro,, DE
- Parts Used:
- WP627843
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker ejector arm broke into.
Removed old ejector arm and installed new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Edgerton, KS
- Parts Used:
- WP67001255
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice maker bucket missing
Needed ice maker bucket for extra fridge. Part came the next day, and worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from WYNNEWOOD, PA
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rail snapped
Followed video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolee from Spokane Valley, WA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light switch broke
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- virgil from Hackensack, MN
- Parts Used:
- WPW10671240, WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
crisper frame and center rail cracked/failed
removed front edge and humidity control levers by popping out with kitchen knife. installed on new crisper frame with new rail and shelf. place assembled unit on brackets. done in 15 minutes and less than $32.00. expected to pay much more for parts. extremely happy thanks to partselect thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Bartlett, IL
- Parts Used:
- WP67006877
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Glass shelf for refrigerator broke.
It was so easy just opened the box took out the shelf and plaed it where the old one was. This was the easiest repair ever. Thank you for this website!
Was this instruction helpful to you?
Thank you for voting!