25344359408 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
ice maker wouldn; dinspense ice'
removed ice denspenser and replaced spring and flap'
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from O FALLON, IL
- Parts Used:
- 242221501
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice auger not working to push the ice to the ice dispenser
Easy to remove the auger Motor and Solenoid, however, it didn't fix the problem. $300.00 into it I now have to purchase a circuit board for $382.00. Not a happy camper.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jubal from OZARK, AL
- Parts Used:
- 241685101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Broken Drum
Had to disassemble the entire ice maker bucket. Simple and straightforward, didn't need any pictures or reference materials. Just time consuming.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Franklin, TN
- Parts Used:
- 5303918344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Replaced Ice Maker
Unplugged refrigerator from the wall plug. Removed ice tray cover, removed ice container, lossen the two screws on the ice marker holding it to the back of the fridge, dropped the ice marker down and unplugged the electrical connection. Then removed the ice maker.
Took the new ice marker, plugged the electrical connection back into the back of the new ice marker, screwed the two screws back in where the ice marker goes and tighen the screws to told the ice marker in place.
Replaced the ice container, replaced the ice cover.
Plugged the fridge electrical cord back in to the wall socket.
Done.
It started making ice again in about 10 minutes.
Took the new ice marker, plugged the electrical connection back into the back of the new ice marker, screwed the two screws back in where the ice marker goes and tighen the screws to told the ice marker in place.
Replaced the ice container, replaced the ice cover.
Plugged the fridge electrical cord back in to the wall socket.
Done.
It started making ice again in about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcus from Bessemer, AL
- Parts Used:
- 5303918344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Ice maker non functioning, Ice maker not sending signal for w
Remove the old ice maker by loosening the screws and disconnect wire harness , next fit new ice maker in place connect wire harness and place new ice maker in place put screws in and tighten.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from FREEPORT, IL
- Parts Used:
- 5303918214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refigerator was freezing and freezer was not
Installed a new Defrost Thermostat.
Was this instruction helpful to you?
Thank you for voting!
the closer plate was cracked and caused the door to catch and make a popping sound.
the repair was so easy to do. it did take 2 of us to handle the door removal and reinstallation. we watched the video and carefully removed the door and had no trouble at all with the new parts installation. we knew what to expect and successfully fixed the frig! Good Deal!! Easy fix!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Washington, IA
- Parts Used:
- 240434301
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator was in storage over the winter and the housing froze and broke.
I removed the screws holding the shield covering the filter housing and cup. Unscrewed the cup, removed the filter. Then removed the pressure fittings holding the water lines on the housing. Then I removed the housing. Reversed the process with the new housing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from VICTORVILLE, CA
- Parts Used:
- 240599803
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The frame for the meat pan in my Frigidaire refrigerator broke in the middle front, which made opening the drawer a little tricky.
No big deal. I took out the glass in the frame, took out the meat drawer, and removed the broken frame, which doesn't take any tools. After removing the frame, I inserted the new frame, which pops in to two clips in the back, and two in the front on each side. I cleaned the glass and put it into the frame. I re-inserted the drawer into the frame. And VOILA!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gene LaFond from NAPAVINE, WA
- Parts Used:
- 240351061
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
closed the door and broke the draw
The repair was not it. It was the customer service by the ladys that answered the phone. Both of them were the same as to give me a perpaid return shipping label and my money back. It was like being at the return desk at W.M. and not like at some of the on line service I have come to know...
Gene
Gene
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from Olden, TX
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Icemaker was producing hollow ice due to water was free flowing out the water dispenser during fill time for icemaker.
Removed old water valve w/ screwdriver, cut threads off old hose (as they just plug straight into new valve) & pushed hoses into new water valve. Solved both problems!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reubon from Phenix City, AL
- Parts Used:
- 240434301
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
water leaking inside of refrigerator from filter area
I just removed the filter and then removed the filter housing. The housing is mounted using two screws. The only difficult part was removing the elbows from the water in and out lines. I don't believe the elbows are reusable. So I would go ahead and order new elbows when replacing this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from WALLING, TN
- Parts Used:
- 241639502
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Fridge started making a loud racket. Condenser Fan Blade then disintegrated to dust and pieces. The plastic had degraded significantly.
The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Hope this helps someone. :)
Was this instruction helpful to you?
Thank you for voting!