59677532603 Kenmore Refrigerator - Instructions

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Saw U tube instrctions how to install and it was easy

Simple placement of new glass pane into crisper top

Empty drawer and take out . remove glass shelf and front and rear shelf braces. remove 2 screws holding pantry end cap to fridge. remove rear bracket by unsnapping clips. remove temp control arm. and reattach to new end cap. reinstall rear bracket to fridge and align end cap, align screws and tighten. reinstall drawers and shelf brackets. replace glass shelf. and reattach lid to brackets. Open beer and enjoy success.

Removed the food bins and lower shelf. Unscrewed the end cap. Removed the drawer hinge. Re-installed hing on new end cap. Installed the new end cap. Re-installed drawers and shelf. DONE!

Great graphics on the website helped to correctly idenitfy the required part. Part arrived quickly and well packed. One of the easiest transactions ever!

Simply fit the frame onto the back piece and lined up all of the anchoring plastic hooks to reattach. I had some minor difficulty in navigating the website but the customer service agent was very helpful and assisted me in purchasing the correct part. Thanks! Gretchen

Replaced the control board. Called another web site and for $15 got the twelve step code to set the new control board.

Still no cooling. Same issue as before.

Sears coming again tomorrow to try again.

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

Took bottom 2 shelves out. 2 screws held assembly in to main cabin. Remove them then 2 additional screws held drawer bracket in place. Easy yet patience and finesse is needed

I replaced both side. The left side I very easy to replace. It has 2 screws holding the end cap in place and the tracking has 2 screws holding it in. Undo the 4 screws and put the track on the new end cap and then you are good to go to install the new end cap on the left side. Now for the right side is easy, but you now have to also undo 2 screws and other 2 for the track just like left side but also you are going to have to undo the humidity control stuff and put it on the new end cap.

It took longer to empty the items off the shelf than it did to do the repair. Slid the veg, drawers out, set them aside.Took glass shelf out set it aside. removed three screws with 1/4in socket. Removed end cap. replaced with new end cap, replaced screws, cleaned and replaced shelf and drawers. Was a very easy task. these pegs break very easy, this is the second time I have had to replace the end cap, both times it was the left size. problem is you have to buy both the left and the right side together,

Pulled old gasket off door put new one in channel on door pushed gasket in channel less than 10 minutes

Open the existing cover and carefully with the thumb and index fingers, pry the cover at over the left pin and remove the cover. Place the replacement onto the right pin and pry the left placing it over the left and you are done.

last time i tried it right away after removing from shipping box.. relaxing with with hot air gun... was not to easy... this time i allowed gaskets to relax for a week on a flat surface. in a warm room.... took less than 5 minutes per door.... no hot air needed.... VERY easy.

An ideal opportunity to clean the tracks for the glass top and sides. I just removed the two (2) screws with nut driver and gently eased the end cap off by slightly pulling it forward and up, inserting the lid onto the new endcap and slipping the cap back into place securing with the two screws. as easy as pie. I did not change the right end cap as there was no need for it, But if U have to change it U must also first disconnect the back plate.