10662159110 Kenmore Refrigerator - Instructions

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

So easy! Nice to have the parts available and promptly delivered-

The repair was very easy, unplug ref. open freezer door, and remove base plate, then remove screws on back plate. I had to tilt top of back plate to remove from freezer. This gives you access to the evap. fan Pull of the three wires, and remove screws from fan bracket, which bolts to the back of ref. Remove fan motor from bracket (2) screws, remove motor, and put replacement motor on bracket, pull fan blade off old unit and push on new motor shaft. Reverse the installation, and you are done. Pretty easy.

Viewed the viedo - it showed what to do

1. Turn thermostat down to ensure cooling cycle turns on. Open freezer compartment and listen for air flow/fan. If no air flow or fan, but compressor seems to be working, then proceed to next steps. 2. Turn thermostat up to shut off refrigerator cooling cycle. 3. Open freezer and remove wire shelf (if installed). 4. Using nutdriver or socket set, remove screws securing metal panel on the back wall of the freezer interior. 5. Pull metal panel out to expose evaporator fan and evaporator coil. 6. Ensuring area around fan is clear, turn thermostat down to again start cooling cycle and check if fan operates - if not, then fan needs to be replaced. 7. Turn off refrigerator and unplug from electrical outlet. 8. Order replacement fan (unless you happen to keep one in stock). 9. Remove two screws securing fan and fan bracket assembly to back wall of freezer, note wire connections to fan (red, white and green), disconnect wires and remove fan assembly. 10. Gently pull off fan blade, it is a compression fitting. 11. Remove two screws holding back and front fan brackets together and remove fan motor. 12. Remove rubber gasket from front and back of old motor and insert then on the new replacement fan motor (these rubber gaskets align to openings in the fan brackets, thereby holding the motor in place when installed back into the brackets). 13. Reinstall fan brackets onto new motor matching how the old motor was assembled. 14. Press the fan blade onto the new motor shaft. 15. Reinstall fan motor assembly onto back wall of freezer. 16. Reconnect wires to new motor as they were previously connected to old motor. 17. Reinstall back wall metal panel that covers the fan motor assembly and evaporator coil. 18. Reinstall wire shelf (if applicable). 19. Plug refrigerator in and adjust thermostat to normal setting to initiate cooling cycle. 20. Open freezer and listen for fan and airflow, if you hear it operating correctly, then close freezer and refrigerator and confirm temperatures after refrigerator has cycled through one full cooling cycle - adjust thermostat as necessary. 21. Tell your spouse or significant other that for less than fifty dollars you just saved the price of replacing the refrigerator.

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

emptied the cracked bin, lifted it out of the door and put the new one in its place, put the items removed from the old one in in and closed the door.

After plugging in the new relay to no avail. I replaced the thermostat. That fixed the problem.

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

I did remove the run capacitor of the starthing kit of compressor and another one new. It work fine.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

We ordered the door shelf bin in the morning and received it the next business day! Great service, very easy process and much appreciated!