10667384801 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jacqueline from LEXINGTON PK, MD
- Parts Used:
- WPW10662129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
No cold
Like you video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from FORD CITY, PA
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer occasionally had a temperature alarm.Clicking noise also.
Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Colorado Springs, CO
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
freezer and refrigerator compartments not cold enough
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- guadalupe from RIALTO, CA
- Parts Used:
- W10124096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Motor sounded like a small little airplane under my fridge, very loud.
Unplugged the fridge first then took the bottom panel off with a 1/4 inch nut driver. Disconnected the wiring & used my ratchet to reach the 3 screws that held the motor. Took me longer to clean the bottom of the fridge then the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from PLAINVILLE, CT
- Parts Used:
- WP2218132K
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drawer broken
Replaced the drawer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from SAN ANTONIO, TX
- Parts Used:
- WP2218132K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the meat drawer was broken.
I was prepared for the part not to fit because it's a 23-year-old fridge, but it fit perfectly, no issues whatsoever. I plan to buy a crisper drawer as well. Glad I found this vendor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolee from Spokane Valley, WA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light switch broke
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from RALEIGH, NC
- Parts Used:
- W10124096
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Replacing Condenser Fan
I was anticipating that the fan would be facing the back of the refrigerator. It actually was perpendicular to the back. There was some difficulty removing the bolts of the fan. I persevered and was victorious.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BLACKLICK, OH
- Parts Used:
- W10124096
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
loud griding noise
stopped the fan and noise stopped ordered fan motor and fan with interface cable. Using 1/4 inch nut driver to remove screws from motor bracket installed new motor and runs like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from BULLHEAD CITY, AZ
- Parts Used:
- W10124096
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Noisy condenser fan
I suggest following video supplied with order confirmation perfect fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Regina B from ST MARTINVLLE, LA
- Parts Used:
- WPW10421486
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Missing retainer bar for freezer shelf
Retainer bar was a little long but husband used a saw to make smaller (the part said it was a similar to my model- Maytag no longer made this made) It was perfect -- ow I have a whole new usable shelf!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- asberry from SAINT LOUIS, MO
- Parts Used:
- WPW10189703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
first a loud noise than noise stopped then the refridg. stop cooling like it should
after finding out what could be the problem I order my part which I got around 3 days unboxed it and replaced it in the freezer component which I had already dismantled made note how I took it off and replaced it in the same way took about 25 to 30 minutes quite easy for me was grateful for the solution and proud of myself after replacing it and it began to work now it's freezing and getting cold as it should Thank you my part store
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Nags Head, NC
- Parts Used:
- W10854037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
2 broken crisper drawers
We went online, found the part, and had it delivered to our rental house in Nags Head, NC. It was the easiest thing ever.
Thank you
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from GLENDALE, AZ
- Parts Used:
- W10854037
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Big handed grandson handled to rough
Took everything out of the old one, lined the new one with cloth and put everything back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from GROVESPRING, MO
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
light did not work on the refrigerator side
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
Was this instruction helpful to you?
Thank you for voting!