59666032702 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Andrea from Swampscott, MA
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken chrisper center rail
Removed the glass shelf, position the rail in its slots and replaced the glass shelves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred M. from Watertown, MA
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
crisper rail cracked at rear top.would stay in place
Removed both crispers and shelf . Inserted new rail as explained in video. Replaced everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from worton, MD
- Parts Used:
- WPW10503278
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Freezer to cold over coollin and no cooling on fresh food
Dropped down the front control panel were you program the the tempertures when you open the doors. This just pops down from the front. Then change out the printed cicuit broad two wires all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Southport, NC
- Parts Used:
- WP67004977
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator door not closing automatically.
Replaced door closer part on hinge. Did not fix problem. Be sure to order mating bushing that goes in the bottom of the door . Part #67004977
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heidi from Etters, PA
- Parts Used:
- WPW10503278
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Freezer freezing up in back and frig getting warm
This is the 2nd Jazz board that we replaced in 2 years. We believe that a power surge caused the board to no longer work. We now have the fridge plugged into a surge protector. The instruction sheet to program the jazz board did NOT come with this part. I called Parts Select and they gave me a number for Whirlpool. I spent over 30 mins. talking to Whirlpool, 2 different departments, and they do not have instructions for this part. I was told that they only supply instructions for about 10% of the parts that they distribute. I was able to find the instruction sheet on my own but searching "whirlpool instruction 16022940." I hope this helps!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Webster, NY
- Parts Used:
- WPW10503278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
fresh food section warm freezer section cold
Found instructions on You Tube how to replace Jazz P/C Board Replaced board and manually defrosted evaporator coil.Everything seems to be working fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Hudson Falls, NY
- Parts Used:
- WPW10503278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Defrost Cycle noy Functioning
Found Board location and replacement instructions on Appliance Doctor website. Price there was actually 3 $30.00 cheaper.Had to remove light cover to access slots to insert a flat blade screwdriver which you use to depress tabs to unlock control board housing. It then swings down so you can unplug wiring harness's and remove and replace control board. Too early to tell if defrost is working yet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Flanders, NJ
- Parts Used:
- WPW10655367
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Old drip pan had many cracks and leaked
Removed back cover. Removed fan with mount which was a little difficult. Installed new pan and parts that were removed. Part came in one day. Great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Columbiaville, MI
- Parts Used:
- W11177593
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer seal was broken
Thanks to some reviews we found online about replacing gaskets, ours went very smoothly. One person said to soak the gasket in hot water, which we did til it was very soft. Installed like a breeze. Then, the same person said to tape the door closed after installation, we did that too. The gasket looks like it was professionally installed and we have never done it before. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Gordon, NE
- Parts Used:
- WPW10503278
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer was frozen over
I popped out the electronic control board and replaced it with the new one. After following the programming instructions provided with the part, the refrigerator/freezer worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Staunton, VA
- Parts Used:
- WPW10503278
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer keept freezing with ice buildup and would not automatically defrost
I used an internet link that the customer service lady provided to assist me in learning the proper removal method, so I could replace the part. So far this seems to have fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burton from Pecatonica, IL
- Parts Used:
- WPW10662129
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Heard a five second buzzing sound repeated 4 or 5 times per cycle coming from rear lower left compressor side.
Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Folsom, LA
- Parts Used:
- WPW10128551
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Fridge section too warm and freezer cold
The unit has two fans on it. One is located in the back and the other is locate inside the freezer section behind the panel. Remove the four bolts holding the door to the sliding rack. Remove the ice machine. Remove the back panel. Noticed that the fan was covered in ice thus shorting the fan motor. Tested for voltage to the fan was good. Replaced evaporator fan motor and unit works perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from Mission viejo, CA
- Parts Used:
- WPW10503278
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer Super Cold, Fridge Hot. Ice on the back of freezer door.
I initially thought the defrost heater or sensor were bad and replaced them. About a week later the problem reappeared. I ordered the control board assembly and after arrival I did the following: Went on-line, located the part on the fridge parts diagrams and figured out how to remove the controller cover (use two flat screwdrivers from behind). After the cover removal unplug the two connectors and lift out the sensor from its mount. Remove the LED Display/Button Board then the microcontroller board. They literally lift out. With the new controller you have to gently break the display board from the controller - the board is scribed along the break-away area. Do this on a flat surface. The actual board installation and hook-up took less than 5 minutes to reassemble. MAKE SURE THE REFRIGERATOR IS UMPLUGGED - I should have said that FIRST.
Was this instruction helpful to you?
Thank you for voting!