25344383406 Kenmore Refrigerator - Instructions

The radiator was not being properly defrosted and the refrigerator and freezer could not keep the temperature. Two things can be causing this, the defrost module which defrost the refrigerator on a regular basis ($110) or the thermostat ($18). I tried the thermostat since it is very easy to do (remove cover plate inside the freezer, cut wires of old thermostat, connect new thermostat by stripping wires. Presto...however the thermostat was NOT the problem. The problem was a blown timer circuit board that controls the regular defrosting. That repair was done by a technician. The board was $110, it seats inside the refrigerator in the control panel area.

Unplug turn water off
Removed two screws with nut driver loosen one
Disconnected three solenoid valves
Disconnected four water lines
Plug tubing in, tighten one flare fitting
Reattach wires to solenoids
Slide under loose screw, replace two screws
Turn water on check for leaks plug in get a drink of water

Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror

When the ice maker is over filling, either the valve is defective or clogged, or the ice maker is at fault signaling the valve to stay open too long. My problem was the latter. I had already replaced the valve, thinking that being only 2 years old, how could the ice maker be faulty. I was wrong. Ice maker unplugs and comes out with 2 screws. A quick swap with the new ice maker and all is well. Simple

The door has nylon gear teeth that wore out and needed replaced. The ice chute came off very easy with 6 screws. I used a punch and pliers to remove the hinge pin. Then the door came off and the new one put on. Very easy. The part was ordered on Sunday and arrived on Tuesday.

Just pushed the button along side the filter and it popped out in my hand. I unpacked the new filter module and inserted it. It was necessary to run water through the dispenser for a couple of minutes to purge the air and clear the lines. The modular filter assembly is more expenseve than some but the ease of replacement makes the cost a good value.

Tried replacing water filter first. It stilled leaked, so I removed the covers to gain access to the water filter base. After cutting the two hoses to remove the old base, I simply slid the hoses into the new base, screwed it into place, replaced the covers, and then reinstalled the new water filter. No more leak!

Unpluged the item. Turned off the water source. Removed the card board cover. Dis-connected the water hoses. Unpluged the connetors. Matched up the colores and put it back together, very easy. Everythings was color coded.

I shut off the water supply and removed the 4 screws from the cardboard back revealing the water valve. I removed the 2 screws which attach the valve to the refrigerator and removed the water valve. Once out it was a snap to unplug the electrical leads and unscrewed the water lines, Insalling the new part was a matter of reversing the above procedure. Everything is color coded which made this replacement extrememly simple.

I will definitely use you guys in the future. The ordering process was great and delivery time was ultra quick!
Thanks for an easy part replacement and simple install.

most importantly on the page with the necessary part..cripser support for the refrigerator--- there was a brief insructional video on how to properly dislodge the broken part and replace it with the new showing the simple tools needed. I am not handy at all but it took me all of two minutes thanks to the helpful video.

Just opened the filter storage and popped out the old one and put in the new one. Ran the system for three minutes according to directions and it worked fine.

- Unsnapped old light socket from top of Frig
- Disconnected elect wires
- Reconnected elect wires to new light socket
- Snapped new socket in place
- Done in less than 2 min.

Once I recieved the new filter, I enthusiastically opened the box, removed the filter from it's packaging and set it aside for quick access. I opened the refrigerator door, pushed the release button on the old filter and pulled it out. I then tossed the old filter in the trash.
Once that was done, I removed the 2 rubber caps covering the inlet and outlets on the new filter. Then, with ace precision, I guided the new filter back into the slot until it clicked. I ran the water for 3 minutes as the instructions suggested, then, had a glass of water.
Mission accomplished and it went off without a single hitch!

Glenn Walker, Simi Valley, Ca

First removed the drip tray with a firm tug, Then removed the 2 screws to remove the trim, had to remove the board to get get to the connector. (there is a clip that holds the wire tight) connected the new ribbon cable and secured it with the clip, screwed the board back in and pushed in the other end of the cable. and screwed the trim back and the drip tray. surprisingly Very easy to do.

Removed the trim screw on top of the door then removed the two hinge bracket bolts. lifted the door
off placed on the table. Remove the two screws on
holding the bearing bracket on the bottom of the door.
removed the bearing and replace with the new one.
Reinstalled in reverse order.