25368253800 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rita from Lake Luzerne, NY
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
first fresh food too hot, then freezer too hot
Based on the website I decided it was most probably the defrost timer, and that was correct. I ordered it, watched the video, and two days later the part was at my door. Took the nut driver, removed 4 screws, then removed the old defrost timer, installed the new one, re-installed the whole plastic assembly with the four screws, and done!!! Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Jonesboro, GA
- Parts Used:
- 240495804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wife didn't like the upper freezer door bin.
Replaced it with one like the lower freezer door bin. Very easy, just snapped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Grants, NM
- Parts Used:
- 215846602
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Defrost timer was not working
Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kasey from O'Fallon, MO
- Parts Used:
- 240338101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
had no shelf bin
Just snapped it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from NEWHALL, CA
- Parts Used:
- 5303918549
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Evap fan motor comes on and off will not stay running
pulled back panel to get at evap fan motor cut wires to remove reinstalled hooked up wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from VIRGINIA BCH, VA
- Parts Used:
- 241554901
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Door switch was no longer making my light go on when door opened
I used the youtube you provided. It was pretty straight forward, but I had to make a trip to the hardware store for a bit (hex wrench) to remove the hex bolt head style screws. I was only expecting to need phillips or flathead. I managed to remove one with a set of pliers, and the brought that example to the store for size reference when buying the bit to fit my black and decker drill. The rest was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Bay City, MI
- Parts Used:
- 5304464438
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Fridge quit working.
A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from POMONA, CA
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken right side rail on meat drawer
Removed two top trays, fixed the rail on the second tray by removing one screw and sliding out broken piece, and sliding in new arm and rescrewing. Screw was a little tight, but went in.Very impressed i was able to do it myself with your simple instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James B from HAZLEHURST, MS
- Parts Used:
- 240356217
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer cold, ref warm.
Removed back panel in freezer and found heater burned into. Found this site on google, looked up part and ordered. Removed old heater and snapped in new one being careful to get it in the fin groves and securing with the same clip straps that that held the old heater in place. Replaced rear panel and plugged in ref. Woks like new! Very pleased with results.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benton R. from Elkton, VA
- Parts Used:
- 240495804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Hook on end of snap-on freezer bin broke.
The existing bin fell off when the hook broke as the freezer door was opened. Finding and ordering the replacement part was about as simple as it can be. Delivery time was less than a week. Replacing the bin was just a matter of snapping it in place, which took all of 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from N LAS VEGAS, NV
- Parts Used:
- 240350609
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The glass shelf broke above the 2 drawers on the bottom
Just lay the new glass shelf into the groves. The shelf was too big and would not fit properly down into the groves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from LAGO VISTA, TX
- Parts Used:
- 240356501
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic runner broken
Got the part. Watched the video. Replaced the Meat Drawer Rail. Just lke that! Easy squeezy! Thank you for making it so simple! ***** (that's five stars!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CHICOPEE, MA
- Parts Used:
- 240495804
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
None fit perfectly
Just slid it down into place.
Was this instruction helpful to you?
Thank you for voting!
Meat drawer rail broken
Removed the meat drawer and shelf from refrigerator. Removed 1 screw from right side rail. Slid rail forward and removed from slot. Inserted new rail into slot, and aligned with screw hole. Installed screw. Repeated process on left side rail. Reinstalled shelf into slots and slid meat drawer into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- earl a from GIRDLER, KY
- Parts Used:
- 218906802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light blub blew
unplug power from ref removed old light socket only difference wired a little different checked new socket compaired to old checked terminal ends small big looked at wires big,little plugged up put in new light blub plugged ref power back on work power off pushed socket bac in power on works
Was this instruction helpful to you?
Thank you for voting!