59676262700 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tom from Summerville, SC
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The icemaker quit making ice.
With instructions from PartSelect.com this was an easy fix. I tested the motor's electric as suggested and was satisfied that the Motor Module (WPL W10190935) would correct the problem. UNPLUG THE REFRIGERATOR! I popped the outside plastic cover off to expose the unit. (1) remove the wire unit that runs the length of the cube maker (2) remove the 3 screws that secure the motor unit and carefully remove it (3) carefully line up the new unit, slide in place and replace the 3 screws (4) install the wire that was removed in step(1). Connect electric to the refrigerator and wait about 2 hours for your first ice cubes. PartSelect.com is the ONLY supplier that you will ever need! Great instructions and trouble shooting suggestions. Shipping is incredibly fasssst! Customer contact is awesome. Don't hesitate to buy from them! Saved me about $200.! Good luck....Tom in SC
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Clarkston, MI
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water dripping in ice cube holder
We removed three screws, unplugged the wire and then removed the old ice maker. Installed the new ice maker with the screws, plugged in the wire and shortly after that we had ice! I was nervous about this repair but it was so easy and the part was here in three days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Selma, IN
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Icemaker motor quit
This was a snap. Loosened 3 screws, removed
old ice maker. Made cutout for water chute. Plugged in
wiring harness plug. Installed new ice maker. Tightened 3 screws.
These brain surgeons that charge $80.00 just to show up at my house to repair an appliance are history.
old ice maker. Made cutout for water chute. Plugged in
wiring harness plug. Installed new ice maker. Tightened 3 screws.
These brain surgeons that charge $80.00 just to show up at my house to repair an appliance are history.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clinton from EUSTIS, FL
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The ice maker only make two cubes of ice per tray
I replaced the old icemaker with a new one but the problem is still occurring in the new one. It only fill with enough water to make about two ice cubes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WARREN from JACKSONVILLE, OR
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Stopped Making Ice
Followed on line video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from GEORGETOWN, TX
- Parts Used:
- WPW10534162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broke my original Kickplate Grille
knelt down, positioned replacement kickplate; popped into place, stood up!
took longer to open the box and peel bubble wrap off item than to replace it!
took longer to open the box and peel bubble wrap off item than to replace it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Troy, MI
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
replaced non-functional ice maker
After first unplugging the refrigerator from it's electrical power source,I removed the lower screw of the ice making unit with a nut driver. I then loosened the upper two screws which hold the retainer clips that secure the unit tight to the freezer wall. I then lifted the unit upward and outward a few inches to allow access to the wire harness. I unplugged the haness from rear of the freezer and removed the unit completely.
To install just reverse the procedure.
To install just reverse the procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Henderson, NV
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker needed to be replaced as it quit working.
Loosened two top screws using a hand held mirror and screwdriver and removed a bottom screw then unplugged the unit inside. Five minutes and repair was complete. Easy as that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Green Valley, AZ
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker would not turn off. Kept making ice! Even turned off all water to house, but then realized that ice maker was being fed by pressurized RO tank!!
Broken plastic part in motor assembly. Very simple to replace. Sears wanted $322.00!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Santa Maria, CA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice tray leaking
Super! It was so fast and easy to fix. Receive my kit in three days and save a lot of money not having to have a repairman come and do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Tucson, AZ
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Unit would not cycle and dispense ice. After replacing with new unit I disassembled old unit and detected a slight burn smell in the timer.
Unplugged refrigerator and turned off water supply. Loosened two top screws and removed bottom screw. Althought kit was supplied with multyple wiring harnesses the harness attached to unit was the correct harness for the model I was replacing. Removed and reused old shut off arm as replacement arms were shorter in reach then original. Also reused bottom unit support that was removed and replaced with one screw into unit and then into side wall of freezer. Over all time less then 15 minutes. As this was a side by side ref/freezer unit their us limited space to view support screws. I used a mechanics mirror to find upper screws. This visualization made the process go much faster. Reading the other repair stories also gave me a huge confidence boost and insite in what to expect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monte from Longview, WA
- Parts Used:
- WPW10534162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I purchased a display model that was missing a part.
Snapped on the new toe grille.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Bakersfield, CA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
heating element going bad
I removed three sheet metal screws, unsnapped the electrical pigtail. Then snapped out knock out on new maker. Matched the electrical connection, pushed it in place. Finally set new one in place, leveled it, tightened the scews and walked away.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Ewing, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
ice maker quit
i noticed that no water was getting to the ice maker. rather than messing around with parts, i bought the entire unit. easy to remove old one and install new one. thanks...ice started again in about an hour. unit cost less than a service call!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doyle from Winchester, VA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker was not working.
On my particular model refrigerator I only needed to remove one screw and disconnet the plug. I then slid the unit out. The new ice maker did not come with the plastic sled that was attached to the old unit. I removed and attached the sled to the new unit with 3 screws.
Was this instruction helpful to you?
Thank you for voting!