10677934700 Kenmore Refrigerator - Instructions

I determined that the ice cube maker was no longer heating the cubes so they could be released into the ice tray. After ordering a new unit, taking out four screws and disconnecting the quick disconnect of wires I plugged the new one in and we were back in business.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

ordered the part, pulled out the icemaker unit, removed the module, put the new module in, reinstalled the ice maker unit and let it run.

With instructions from PartSelect.com this was an easy fix. I tested the motor's electric as suggested and was satisfied that the Motor Module (WPL W10190935) would correct the problem. UNPLUG THE REFRIGERATOR! I popped the outside plastic cover off to expose the unit. (1) remove the wire unit that runs the length of the cube maker (2) remove the 3 screws that secure the motor unit and carefully remove it (3) carefully line up the new unit, slide in place and replace the 3 screws (4) install the wire that was removed in step(1). Connect electric to the refrigerator and wait about 2 hours for your first ice cubes. PartSelect.com is the ONLY supplier that you will ever need! Great instructions and trouble shooting suggestions. Shipping is incredibly fasssst! Customer contact is awesome. Don't hesitate to buy from them! Saved me about $200.! Good luck....Tom in SC

Removed ice maker from fridge. Removed motor assembly (3) screws on cover, and (2) screws inside. Removed mold (3 screws on bottom) and replaced everything in reverse order. Note: Turned ice maker off for several days while waiting for parts. The water line on this particular model will freeze inside the freezer if ice isn't made for several hours/days. You will have to defrost to begin making ice again.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

This was a snap. Loosened 3 screws, removed
old ice maker. Made cutout for water chute. Plugged in
wiring harness plug. Installed new ice maker. Tightened 3 screws.

These brain surgeons that charge $80.00 just to show up at my house to repair an appliance are history.

We removed three screws, unplugged the wire and then removed the old ice maker. Installed the new ice maker with the screws, plugged in the wire and shortly after that we had ice! I was nervous about this repair but it was so easy and the part was here in three days.

Followed on line video

I replaced the old icemaker with a new one but the problem is still occurring in the new one. It only fill with enough water to make about two ice cubes

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

I removed three sheet metal screws, unsnapped the electrical pigtail. Then snapped out knock out on new maker. Matched the electrical connection, pushed it in place. Finally set new one in place, leveled it, tightened the scews and walked away.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Super! It was so fast and easy to fix. Receive my kit in three days and save a lot of money not having to have a repairman come and do it!

Unplugged refrigerator and turned off water supply. Loosened two top screws and removed bottom screw. Althought kit was supplied with multyple wiring harnesses the harness attached to unit was the correct harness for the model I was replacing. Removed and reused old shut off arm as replacement arms were shorter in reach then original. Also reused bottom unit support that was removed and replaced with one screw into unit and then into side wall of freezer. Over all time less then 15 minutes. As this was a side by side ref/freezer unit their us limited space to view support screws. I used a mechanics mirror to find upper screws. This visualization made the process go much faster. Reading the other repair stories also gave me a huge confidence boost and insite in what to expect.