25356943601 Kenmore Refrigerator - Instructions

Bought a new
capacitor.

I want to first say that before I ordered this part from "Part Select" I first went and talked with a local appliance repair shop. They quoted me a $120 charge to come out and check the problem. Then $30 and hour service fee, plus parts. He provided me a quote of about $250 for the job.
I found this part easily on the web site $77. It was very easy to instal. The only problem I had was the fact that in the side by side it was very difficult for me to get two hands inside the freezer to install it. (I have wide shoulders). Two screws loosened, no need to remove them. Just life the entire unit straight up. Unplug wire harness. Then just reverse order. Could not be easier. If you can change a light bulb you can do this.

Simply slid glass into frame & it fit perfectly.

Removing the old unit was easy enough, just loosened two screws that attach unit to side of freezer and disconnected the wiring harness. But the new unit never goes in quite as easily because it's always just a little different from the original. In this case, the wiring ended up being about six inches longer and the excess had to be stuffed behind a shield at the rear of the unit. Theoretically, the wire could have been pushed back through the opening, but it got jammed and wouldn't go. I had to remove side rails and pry the shield forward in order to get the wiring back out of the way. The unit is a narrow side by side, so there wasn't a lot of room to move around. But it wasn't difficult, just tedious. I had to make sure the wiring did not come into contact with the heating element at the bottom of the icemaker. Once installed it worked great.

The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!

First of all Don't panic! you can do it and you can save a lot of $$$ if you do it yourself. A friend advice me to look it up online resources and came accross part select on YouTube .

The process:
Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.

The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.

Followed the steps in the video on your site, really easy to do.

The biggest part of the repair was getting everything out of the shelves in the door. I had to remove one phillips head screw from the plastic hinge cover on the top of the appliance. As per the owners manual I traced around the hinge with a pencil so I would be able to align the door to the same postion. Removed two screws with a nut driver and removed the top hinge. The magnetic strip held the door in place until I grabbed it and pulled it open then lifted it up off of the bottom hinge. I layed the door on the island counter and pried the bearing hinge out of the door stop and replaced it with the new one. I probably could have stopped there but figured the plate might have been worn so I remove one phillips head screw from the bottom hinge, lifted the plate off, and replaced it with the new one. I assembled everything in reverse order and voila, no more popping noises.

First of all, I ordered in the afternoon and the part was on my doorstep the very next day, amazing shipping. I shopped all over and this was the best price by a few dollars. I hope I never need any other parts, but if I do, I will come back to buy my parts here.

I pried the old cover off with a pocket knife and carefully installed the new one. Now it looks great and it only took me about 5 minutes.

-unplug power cord.(safety first!
-Removed evaporator cover in freezer. found defrost thermostat defective.
-use hair dryer to manually defrost coil from ice build-up.
-unclip thermostat from coil.
-cut wires close to the defrost thermostat; remove defective thermostat.
-clip on new defrost thermostat.
-connect wires using included butt connectors including shrink tubing (also included)
-replace coil cover.
-plug power cord back in.

This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

take out screws front control panel ,then screws on left panel holding control unit. had to clean up plastic she got a little toasty. unhooked control unit replaced with new and reassembled. The real story is in your excellent web site easy to find exactly what I need and with prompt shipping, I was back in service quicker than having someone come out and repair.

Great Job
Jeff Baker

Removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the wires. Everything matched up perfectly.

Removed supports with pliers and used center punch to push broken plugs out of hole and inserted the new supports.