59667953602 Kenmore Refrigerator - Instructions

Take everything off the top self, lift the self install the new part ,put self back in place and then install the drawers again. Took minutes.

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

removed three screws pluged it in and it was ready to go. I must add That I ordered it one day and received it the next day by fed ex. I could not believ how fast the service was also the new icemaker is working great. I will order any furture parts I need from Parts Select. Also have given your web site ot several other people. Thank you very much.

Ice maker wouldn't eject the ice often enough. After reading a few other stories, I just ordered the universal ice maker from Part Select. All I had to do was remove some of the plastic shrouds from my old ice maker and put them on the new one. I also reused my mounting brackets. The whole job took me 20 minutes.

I removed three sheet metal screws, unsnapped the electrical pigtail. Then snapped out knock out on new maker. Matched the electrical connection, pushed it in place. Finally set new one in place, leveled it, tightened the scews and walked away.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

It was exactly as everyone else described--remove old ice maker, unplug, plug in new ice maker, attach new ice maker. 3 screws, 1 plug. My plug was the one on the ice maker not on the refrigerator (ie I used the wiring/plug that was already in the freezer).

On my particular model refrigerator I only needed to remove one screw and disconnet the plug. I then slid the unit out. The new ice maker did not come with the plastic sled that was attached to the old unit. I removed and attached the sled to the new unit with 3 screws.

Bought a new shelf

Caused the shelf on my fridge to break a ladder hook. I didn't even know where to begin looking for an Amana refrigerator shelf mount bracket, but luckily found this website from a Google search. The part was super easy to find, arrived in two days, and was a snap to install. What did people do before the internet?

The instructions are practically no help, but if you study the diagram, you can figure out the one screw you need to remove. Then the icemaker lift off of two brackets. I couldn't see how to use a screwdriver to unlock the bracket, but just applying mild pressure and pulling it forward brought it right out. I didn't have to change anything with the plug already intalled so it was very easy to pop in, lock the plug, pop into brackets, replace screw and I was in business. 24 hours later I had a bucket of ice! 15 minutes to figure out how to get old out and 5 min to replace new one. Fairly easy. Read posts here to get hints!

Removed the screws and disconnected the electric. I put the proper electric harness on and went to fit the unit in but it didn't fit. Until I figured out that you have to use the clips from the old unit that hold the unit in place. The actually hang on them. Once I figured it out it was easy.

Unplugged refrigerator and turned off water supply. Loosened two top screws and removed bottom screw. Althought kit was supplied with multyple wiring harnesses the harness attached to unit was the correct harness for the model I was replacing. Removed and reused old shut off arm as replacement arms were shorter in reach then original. Also reused bottom unit support that was removed and replaced with one screw into unit and then into side wall of freezer. Over all time less then 15 minutes. As this was a side by side ref/freezer unit their us limited space to view support screws. I used a mechanics mirror to find upper screws. This visualization made the process go much faster. Reading the other repair stories also gave me a huge confidence boost and insite in what to expect.

i noticed that no water was getting to the ice maker. rather than messing around with parts, i bought the entire unit. easy to remove old one and install new one. thanks...ice started again in about an hour. unit cost less than a service call!

Loosened two top screws using a hand held mirror and screwdriver and removed a bottom screw then unplugged the unit inside. Five minutes and repair was complete. Easy as that!