59669942010 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Don from Bozeman, MT
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Flange broke off the center rail
Took off the broken rail and dropped in the new one with only a slight pressure of the plastic shelf frame shelf. Took about 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from Smithfield, UT
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Crisper Centr Rail which holds two Crisper drawers needed to be replaced as drawers were slliding on bottom of refridgerator
Pull out the drawers and removed the old rail, place new rail in and return drawers. Like New and took about 3 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from Dexter, MI
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken center crisper rail
removed the shelf inserted the new rail, replace the shelf and the crisper bins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from McCall, ID
- Parts Used:
- WPW10671238
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Our center rail that holds our refer drawers broke.
I placed the back of the bracket into the slot in the rear of the refrigerator and stretched the front plastic rim on the glass shelf over the front of the new center rail until it snapped into place (all the while hoping I didn't cause further damage to my refridgerator!) and wa-la, piece of cake! My impatience paid off this time!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heidi from Yellow Springs, OH
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Center crisper rail broke.
I took the shelf and drawers out and replaced the rail, put the shelf and drawers back in. Easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrea from Swampscott, MA
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken chrisper center rail
Removed the glass shelf, position the rail in its slots and replaced the glass shelves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from LOMBARD, IL
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke insert piece
Followed easy instruction video. It was like new in fifteen minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred M. from Watertown, MA
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
crisper rail cracked at rear top.would stay in place
Removed both crispers and shelf . Inserted new rail as explained in video. Replaced everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burton from Pecatonica, IL
- Parts Used:
- WPW10662129
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Heard a five second buzzing sound repeated 4 or 5 times per cycle coming from rear lower left compressor side.
Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Folsom, LA
- Parts Used:
- WPW10128551
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Fridge section too warm and freezer cold
The unit has two fans on it. One is located in the back and the other is locate inside the freezer section behind the panel. Remove the four bolts holding the door to the sliding rack. Remove the ice machine. Remove the back panel. Noticed that the fan was covered in ice thus shorting the fan motor. Tested for voltage to the fan was good. Replaced evaporator fan motor and unit works perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from worton, MD
- Parts Used:
- WPW10503278
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Freezer to cold over coollin and no cooling on fresh food
Dropped down the front control panel were you program the the tempertures when you open the doors. This just pops down from the front. Then change out the printed cicuit broad two wires all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from Mission viejo, CA
- Parts Used:
- WPW10503278
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer Super Cold, Fridge Hot. Ice on the back of freezer door.
I initially thought the defrost heater or sensor were bad and replaced them. About a week later the problem reappeared. I ordered the control board assembly and after arrival I did the following: Went on-line, located the part on the fridge parts diagrams and figured out how to remove the controller cover (use two flat screwdrivers from behind). After the cover removal unplug the two connectors and lift out the sensor from its mount. Remove the LED Display/Button Board then the microcontroller board. They literally lift out. With the new controller you have to gently break the display board from the controller - the board is scribed along the break-away area. Do this on a flat surface. The actual board installation and hook-up took less than 5 minutes to reassemble. MAKE SURE THE REFRIGERATOR IS UMPLUGGED - I should have said that FIRST.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bea from Grand Rapids, MI
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The Rail broke
Removed the storage bins. Removed the whole shelf, remove the glass part.(clean everything while you are at it, which is why it took 15-30 minutes) Lift out old rail and replace it with the new, reinstall shelf and glass. If you choose to not to clean, just take out the glass shelf, replace rail and put it back in. .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Gordon, NE
- Parts Used:
- WPW10503278
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer was frozen over
I popped out the electronic control board and replaced it with the new one. After following the programming instructions provided with the part, the refrigerator/freezer worked great.
Was this instruction helpful to you?
Thank you for voting!