59667254601 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carlton from CHICAGO, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light out.
Popped out the old switch and replaced it with the one dying
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from WILMINGTON, MA
- Parts Used:
- WPW10671238
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken center crisper rail
Lift off glass shelf and insert tabs of rail on each end , replace shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helene from Matawan, NJ
- Parts Used:
- WP67001716
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Ladder hook for shelves broke.
Hook just clips right into the channel in seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Laurel, MD
- Parts Used:
- WP67002633, WPW10671238
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
The center crisper rail for the crisper pans broke and one of the bins ended up cracking
I removed the crisper pans, installed the new rail and then installed the new bins. Very easily done--I was finished in 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from Westford, MA
- Parts Used:
- WP67001255
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed a larger ice pan for the freezer.
I took out the old one and put in the new one. For some reason the repair story associated with the ice bucket had nothing to do with ice buckets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Lorton, VA
- Parts Used:
- WP67003753
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
Low flow into the ice maker
Unplug refrigerator. Turn off water. Remove water line to inlet valve. Remove mounting screw. Unplug electric connection. Unhook water line out. Reverse process to install new inlet valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary L. from Millsboro,, DE
- Parts Used:
- WP627843
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker ejector arm broke into.
Removed old ejector arm and installed new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from AUBURN, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from JOLIET, IL
- Parts Used:
- WP67002633, WP67001716
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
BOTH THE LADDER HOOKS, AND THE CRISPER PARTS WERE BROKEN
SIMPLY REPLACED THEM
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lawrence from TRAVERSE CITY, MI
- Parts Used:
- WPW10196393
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Noisy, running constantly motor in damper unit.
Unsnapped and pulled off small cover exsposing two phillips head screws. I removed larger cover and styrofoam insert fully exsposing the damper unit. i unplugged same and with a 1/2 inch wood chisel was able to release the "snaps" holding the old unit in place. Simply reverse procedure to install new unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from SAINT ALBANS, VT
- Parts Used:
- WPA3223101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Water line feeding ice maker was not producing ice
Take out the elbow fill tube and check to see if ice build up inside tube. Clean tube of ice build up. Replace tube back in. In my case that corrected my problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Red Banks, MS
- Parts Used:
- 12002497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Freezer Drawer Gear
Checked Video online. Had to remove the 2 snap on track/gear covers. Pry out the gear with screwdriver and the gear bearing unit. Align the flat side of the bearing unit and snap in. Position the cut teeth on the gear to match original and snap into the bearing. Insert the connecting rod into the long shaft gear and then push back into the short shaft gear. The video said to remove the drawer front but I did not and don't see that it necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from HUNTINGTN BCH, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Difficulty removing old switch.
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from WPB, FL
- Parts Used:
- WP67003753
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Leaking water control valve for ice maker
There are plenty of videos showing how to change out this part. What they don’t tell you is that when you are pushing in the supply line into the water control valve it will feel like it’s seated, but it’s not. You have to push pretty hard and it will go in another quarter inch. Now it’s seated. If you don’t see it fully, it will leak out of that hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothea from TOMS RIVER, NJ
- Parts Used:
- WPW10534161
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Easy to clip in place
No tools required, but you must be careful not to shove or jam this kick plate into place as it is a plastic part and not really very sturdy. This is the second time I have replaced the kick plate and PartSelect has always been knowledgeable, polite, and helpful
!!
!!
Was this instruction helpful to you?
Thank you for voting!