25344502601 Kenmore Refrigerator - Instructions

It was real easy took the lines off one by one put them on the new unit one by one same with the three plugs than tighten new unit back on fridge.

Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.

Removed and replace solenoid manifold valve in rear of appliance using inadequate You Tube video. Removed and replaced augur motor after dismantling various housings using a seriously mistaken You Tube video. The latter video informed us that the yoke that screwed on the motor's shaft was a reversed Left Hand thread. It wasn't at all, and we struggled to figure that out. The people that make these videos leave out steps that they thunk are obvious, but aren't at all.

removed ice denspenser and replaced spring and flap'

Had to disassemble the entire ice maker bucket. Simple and straightforward, didn't need any pictures or reference materials. Just time consuming.

Ordered new ribbon cable. At first I couldn't figure out how to get the wide end of the ribbon cable off, and I took the whole inner circuit board out - in fact, all it needed was more muscle, a straight pull out, no clips or anything holding it in other than friction. The narrow end attached to the control button board has two clips which pull towards you to loosen the ribbon. Easy install, worked perfectly

Before removing door, remove everything from on the door including the shelves, then close the door. Using a step ladder to access the top of the door, I removed the plastic hinge cover at the top of the refrigerator door using a Philips head screwdriver, remove the screw located at the back of the cover and slide the cover forward and up to remove. This will expose the two 3/8 machine screws that hold the top hinge bracket. Remove the screws using a socket or wrench. Then lift up on the hinge bracket from the top of the door to remove it. As long as the door is closed it will remain stable with little pressure to keep from falling. Then lift the entire door from the bottom hinge assembly and lay it across an arm chair or flat elevated surface so you can access the bottom door hinge bearing. You will see a bracket screwed to the bottom of the door with two 1/4 machine screws, it is the door stop bracket and this has the door hinge bearing inserted through it. My bearing was broke in half , the first piece fell out when I removed the door and the other piece was still inserted in the door. I removed one 1/4 screw from the stop bracket and loosened the other screw to allow the bracket to swing away from cavity that holds the bearing. Using needle nose pliers I remover the broken piece of the bearing. This part is nylon or plastic and can be cut into pieces if need be to remove it. Once removed, I cleaned the cavity, reinstalled the stop bracket assembly then inserted the new bearing. Gently align the door to the bottom bracket and set it in place, a second set of eyes may help. Once the door has been seated and in the closed position replace door bracket and the two 3/8 screws at the top of the door, check the alignment before you tighten. Check door operation! Then tighten the screws and replace the plastic cover by pressing down on the cover and sliding it back to align the Philips screw to be replaced .

The repair was not difficult because you just remove the old part and plug it in and connect two wires. But I wish there was a way to test if the compressor is working before I purchased the parts. The compressor would not start so I was not able to repair the refrigerator.

Easy to remove the auger Motor and Solenoid, however, it didn't fix the problem. $300.00 into it I now have to purchase a circuit board for $382.00. Not a happy camper.

Removed the door marking the top hinge placement prior to removal. Pulled the door the rest of the way off. There wasn't anything keeping it attached on the bottom right side. Turned the door upright dug out the old broken cam and replaced it with a new one. Thank you for your web-site. It saved us $$$ you have gained two new fans to your web-site. I have shared your link with many. To to anyone who is having a popping noise when you open your door. Do panic. Log on to Part Select .com. It is your only source of sanity.

Thank you

Liz

I removed the screws holding the shield covering the filter housing and cup. Unscrewed the cup, removed the filter. Then removed the pressure fittings holding the water lines on the housing. Then I removed the housing. Reversed the process with the new housing.

Remove the old ice maker by loosening the screws and disconnect wire harness , next fit new ice maker in place connect wire harness and place new ice maker in place put screws in and tighten.

Unplugged refrigerator from the wall plug. Removed ice tray cover, removed ice container, lossen the two screws on the ice marker holding it to the back of the fridge, dropped the ice marker down and unplugged the electrical connection. Then removed the ice maker.
Took the new ice marker, plugged the electrical connection back into the back of the new ice marker, screwed the two screws back in where the ice marker goes and tighen the screws to told the ice marker in place.
Replaced the ice container, replaced the ice cover.
Plugged the fridge electrical cord back in to the wall socket.
Done.
It started making ice again in about 10 minutes.

Installed a new Defrost Thermostat.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.