10656836600 Kenmore Refrigerator - Instructions

Approximately:

1. Unplugged refrigerator.
2. Emptied Freezer.
3. Removed Ice Maker.
4. Waited a few hours for ice to melt around back panel & nuts.
5. Removed back panel and the cover over fan and fan motor.
6. Waited many more hours for ice to thaw over fins, wiring, etc.
7. Easily replaced the bi-mental defrost thermostat.
8. Replaced panel, fan cover, ice maker.
9. Plugged in refrigerator and waited a bit.

This worked! Yahoo.

p.s. I am a 65+ year old mechanically minded woman. :-)

Ordered Part Number and overnighted shipping. Took less than 5 minutes to install the kit. Refrigerator Works GREAT!!! FYI, I called a repair service and they wanted $300.00 to come out and repair. The part and shipping were $76.00. I saved a ton and did it myself!!!

Removing the panels inside the freezer section was the most difficult ,because it is narrow,hard to fit your body inside compartment, in order to cut wires and to splice Bi-metal Defrost Thermostat wires (2 ) Watch the videos on the web site so you know where to start. First time I ever "repaired " a large appliance, saved me over $ 600.00 (that's what the people I bought the Refrigerator from wanted to charge me.) My parts cost 65.00 !!!!! My younger brother turned me onto the web site... , I'll be returning to the site and telling my friends about it. It's a total "rip off" what service organizations charge the general public these days from Car Dealer ships to the stores we purchase our appliances from. !!! Glad I still have my health and faculties to repair the essentials we have around our homes. !!!!

New part slipped right into the studs and fit perfectly

Removed upper hinge cover and hinge, lifted door from lower hinge socket, removed lower cam from 'frig hinge, and replaced with new. I had a helper hold the 'frig door while I removed old upper cam, and replaced with new. Piece of cake and works like new! This must be a design problem..

Remove the unit cover by unsnapping from the bottom. Remove the face plate on the switches. The ice door simply snaps off the closing mechanism. The problem I have is that the original door included a heat trace element (keeps the back of the door warm to limit condensation). The new part was simply a new seal. I clipped the leads to the het trace (turn off the fridge before you do that) and put in the new door. When the heat ids on in the house there is no problem with condensation but on warmer days its pretty bad. I cannot find a replacement part with the heating element and have contacted Whirpool. THey haven't responded as of yet.

We took out the old filter and put in the new one. Ran out a few gallons of water then it was ready to use.

I noticed that everytime I plug the refrigerator cord into to the wall outlet it would trip the shock prevention safety switch on the wall outlet. I came to the conclusion that something was blocking the electrical current to flow to the compressor. I figured if I changed the the part attached to the compressor then the electricity would be able to make a complete circuit to the compressor. so I got the part # from the old part and I researched it through your company. You had the part in stock. I ordered it and it was at my door the next day. It worked extremely well. I proudly can say I did it myself and most importantly I don't need a new refrigerator and I save a lot of money. thanks I will definitely use your company in the future. Ray

I just slid the new pan in , partselect has the correct part all the time , I repalced my ice maker once and it took 15 min no problem

Remove ice maker from freezer, place on its side on table. Remove single screw securing coupling from shaft without removing shaft from housing. Remove old coupling, and attach new coupling using single screw.

This is a great time to completely clean the Ice maker bin and crusher unit.

Unscrew the three phillips screws holding the flipper and electric eye unit, pull it out a bit to unplug the connector. Take the assembly over to a flat surface, and use pliers and or crew driver to pry/pull off the press-on retainer on the hinge pin. Pull out hinge pin, remove the broken flipper. Put new flipper in place making sure spring is behind the flipper (holding it open). Reinsert hinge pin, and then reuse the press-on retainer to hold in in place. Then take the repaired assembly back to the freezer, re-plug the plug, and then reinstall the unit using the 3 phillips screws. Easy Peasy.

I unplugged the refrigerator
Opened the freezer door
Opened the ice maker door so that I could easily get to the emitter and receiver
I used a phillips head screw driver to remove 3 screws from the emitter plate and 3 screws from the receiver plate
I unplugged the faulty circuit boards--this took some tugging
I firmly plugged in the new circuit boards and replaced the screws
I waited about 30 minutes and the ice maker began making ice again

After receiving the replacement emitter and receiver boards from PartSelect.com, I following the troubleshooting paperwork that came with my order to ensure the parts I ordered where the problem. After which, it was very straight forward: unplug the frig, unscrew the 3 screws on the covers for each board, unplug the push-pin connection, remove the board screw, set the new board in, and plug back into the connection. It took approximately 20min.

I didn't have to buy a new Ice door kit. The part on the Refrig. door I needed I found out was unavailable. The door parts (Ice door parts and the asembly for the water unit) screws into that part. I found out that I would have to replace the whole refrig. door which was $900.00. I took every apart got me some pvc glue used it on the door and bought the original screw online with some other assorted parts,Door switch, etc. and was able to repair in about an hour. Some of the parts are very fraigle so you have to be very careful or you will be buying some new replacement parts.The new nickel and dime parts are expensive. My Icemaker was leaking where the Ice was clumping together in the bin, and when I checked the unit was $125.00. I found a new one and replaced it for about half that price. I am now very happy! (a least until the next project.)

First I removed all contents from inside refrigerator door.Then I removed (1) 10mil screw,which holds cover for top hinge.Next I removed the (3) hinge screws,and lifted door off of bottom hinge.Pulled off plastic closure cam from bottom metal hinge post.I cleaned metal post ,applied a small amount of vaseline to post, slid on new plastic cam,installed door, replaced screws.Very easy,10 to 15 min tops.