10657069603 Kenmore Refrigerator - Instructions

I emptied refrigerator contents and tilted the refrigerator to the right so as to access the metal panel upon which the evaporation tray was resting. The metal panel is on the left side underneath the refrigerator and the evaporation tray is resting on the panel. I removed 4 screws that were holding the metal panel, pressed down on the panel, slid out the old, cracked plastic evaporation tray, inserted the new plastic evaporation tray, raised the metal panel to its original position, replaced the 4 screws, being careful not to pinched the water line that feeds the ice-maker. VOILA! Un-tilt the frig and re-stock it. It took a day for the temperature to stabilize, due to tilting, I think. New tray $45.

First I removed the icemaker from the freezer by removing two horizontal screws holding it to the side wall, and one vertical screw holding the front to a bracket coming off the side wall. Then I used a flat screwdriver to unlock the electrical plug. (After doing this, I realized that this wasn't necessary at all, and this part could have been changed just as easily without removing the icemaker.) On the front, there is a white cover with Ice Maker Plus. Use a flat screwdriver to unlock the tangs and remove the cover. There are three screws in the corners that once removed, will allow the motor assy. to be gently pulled straight out. On the back of the part, you will see many gold lands that the timer touches. I don't think there was anything wrong with my motor. I had two spots where the gold plating was worn off, so I suspect it was not making contact, and the whole process would stop. Slide the new part in place making sure the teeth on the gears line up (not a big deal), and secure with the screws. Install cover and you're done. Mine has been making ice like it was brand new.

looked up the model #, found your co. & ordered a new one Service was excellent, shipping reasonable; it was a pleasant surprise. I will tell my friends about your co.

First off, if you have the stainless steel panel inserts on your refrigerator you'll need to remove those to do this repair. I kept looking for the access holes on the underside of the dispenser panel that you're supposed to insert a screwdriver into to pry it off. It wasn't until I removed the freezer door handle, slid the lower stainless panel insert out, and removed the rail just beneath the dispenser that I could see and access these holes. I also removed the upper stainless panel and rail just above the dispenser to allow enough movement get the dispenser cover off and out. The rest of the repair is pretty straightforward. The old ice door was beaten up and not closing completely, this was letting warm air into the freezer which was melting and re-freezing. This kit fixed the problem.

I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.

Thank you
Curtis Hall

Disconnect power to refrigerator. Removed all food from Freezer. Removed all Shelves and shelf clips. Used phillips screwdriver and removed 6 screws from lower rear panel covering evaporator coil. Removed panel. Pulled plastic fan blade off top of motor shaft. Unclip top front of black motor retainer clip which then allowed the rear clip to unhook. Removed clip. Then removed 3 wires from fan motor, noting proper location for replacement. Slide the fan motor out to the left. Installed new motor. Reinstalled clip, hooking rear side first. Then rehooked the 3 wires. Slide fan blade back on top until secure. Tested everything at this point before reassembling rear panel. Then replace rear panel, replace the 6 screws, replace shelf clips and shelves and replace food. Very easy to do and saved about $150 over a service call to troubleshoot and re-visit to install after getting part

Removed plastic door over ice maker remove 4 screws and slide unit out after disconecting pull apart elect. Plug. Pop off side gear cover install on new and slide in, reconnecting electric plug as you go.

Dog chewes up the original part. Got the replacement , put it on the filter turned to lock in place and tried tp pull out old filter ( same procedure has been done multiple times successfully) part broke instantly upon putting pressure tom pull out filter. Sent back to you the next day for replacement.

removed cover the four screws that mounted the motor,unplugged and replaced motor

Removed the icemaker to see if I could determine problem; motor was seized; got part numbers and ordered from you; parts arrived next day (even though overnight delivery wasnt' requested - so THANK YOU!); compared new parts to original to be sure of fit; reassembled unit; reinstalled in freezer, and waited for the sound of water filling the tray. Producing like brand new again! Cancelled the service call w/ Sears for the following week (when it was convenient for them) Loved your service!

The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the plastic arm, which caused the arm to fail. Then reassemble in reverse order.

Replaced 8 cube ice maker assembly. Contrary to instructions I 1st removed 2 screws on the flapper door 2 removed 3 screws in bottom and 1 screw on right side bottom and pulled shelf out unplugged plug and lifted assembly off put new one on shelf plugged it in and slid it back into place replaceing. screws. was done in 10 min. start to finish . so far seems to have solved the problem.

Linkage on the cold-control mechanism in the air diffuser assembly was broken. It was necessary to access the diffuser assembly from both the refrigerator and freezer sides of the unit.
Re-connected the linkage between the diffuser and cold-control assembly; remounted the two combined assemblies . . . refrigerator working nicely now.

Emiter blinking red; ice maker stopped working. Called appliance repair, said electronic control boards needed to be replaced. Quoted me $275, including parts. Ordered part at partselect.com, installed in 15 min and ice maker started producing ice. Also discovered on other online forums that this part is a common failure on these model refrigerators. Very easy to swap out, plug & play. Make sure to unplug appliance before performing repair due to shock risk.

Pulled out the old drawer and put in the new.