59667992606 Kenmore Refrigerator - Instructions

The entire process took lees than 5 minutes. I simply removed the broken rail, and inserted the new one. Voila! Like new!

I placed the back of the bracket into the slot in the rear of the refrigerator and stretched the front plastic rim on the glass shelf over the front of the new center rail until it snapped into place (all the while hoping I didn't cause further damage to my refridgerator!) and wa-la, piece of cake! My impatience paid off this time!

Removed drawers, lifted glass shelf, installed new part

Snapped old one off, snapped new one on

Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.

Followed easy instruction video. It was like new in fifteen minutes.

Removed both crispers and shelf . Inserted new rail as explained in video. Replaced everything.

Removed the glass shelf, position the rail in its slots and replaced the glass shelves.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Found instructions on You Tube how to replace Jazz P/C Board Replaced board and manually defrosted evaporator coil.Everything seems to be working fine

This is the 2nd Jazz board that we replaced in 2 years. We believe that a power surge caused the board to no longer work. We now have the fridge plugged into a surge protector. The instruction sheet to program the jazz board did NOT come with this part. I called Parts Select and they gave me a number for Whirlpool. I spent over 30 mins. talking to Whirlpool, 2 different departments, and they do not have instructions for this part. I was told that they only supply instructions for about 10% of the parts that they distribute. I was able to find the instruction sheet on my own but searching "whirlpool instruction 16022940." I hope this helps!

Replaced the CNTRL-ELEC board with ease. Just slide back and remove the light cover. Use flat tip screw driver to release and drop down unit. Remove connectors and attach to new board after breaking in half to fit same as old one. Programming is easy, just look at the CODE on the name plate inside the door. Mine is 0-1. Follow procedure of holding the light switch off while touching the freezer control 3 times within 10 seconds. A "P" for programming will appear. Still holding the light switch, touch the refrig control to set for your code. Freezer button says 0, refrig button says 1. When you release the light switch, the programming is done. Mine starts out with a 4-4. It is now working quieter than when it was new and is very cold again.

Found troubleshooting steps for control board (called a jazz board) and ran through the steps. Found the control board (jazz board) was bad. Pull front vent cover where the condenser is off, you will find manufacture manual papers for these steps and for programming of new control board (don't lose these papers for next time). Papers are located under bottom of front right corner of refrig where they are in a bag ( cut bag open and replace back when finished for next time). Replaced board by: 1. Pushing light cover to back to remove 2. Take screwdriver and push on two tabs that hold housing on at each side (will see two holes where they are by looking from behind, with your head inside) push and pull down. There it is 3. Replace board with the tabs that hold it in. (use latex gloves and only touch outside of board, to avoid static electricity to the board. 4. Reinstall and program (Code for your refrig is on cabinet sticker where model and serial no. are) 5. Install a surge protector on the plug for possible surges. Not too bad to install, just finding how it comes out .

first unplug unit, remove clear light cover it snaps out. there are 2 slots on either side of the light housing stick the screw driver in the slot and push the tab and pull down this will unlatch the control board housing, remove the board socket plugs, and the board from the frame, on the new board you will have to snap the PC board at the pre indented line. replace in reverse and follow instruction to program the code.

Thanks for the control board. However, it arrived in two days not overnight, UPS noted on their tracking site the error was their own. Also, the part did not come with installation instructions or programming instructions. Found on youtube a video that described in detail the programming procedure: . . . . . very helpful.

Thanks,
Marc