25344352408 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Douglas from Denver, IN
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Water dripped from water outlet on door
Replaced the Triple Water Valve
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from PHILADELPHIA, PA
- Parts Used:
- 240599301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The top crisper drawer frame was cracked, it secures the glass top also.
Replaced the top crisper drawer frame. Installation was very easy. The hardest part was cleaning all of the spilled food/liquid items from under the drawers once removed to replace the top frame. I will keep the top frame and repair it. From what I have read, this is a very common problem as there is no support in the middle of the frame...it is only plastic.
Was this instruction helpful to you?
Thank you for voting!
chrisper drawer jammed found supports were broken
Looked at video on how to remove and reinstall support and followed the instruct ions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RANDY from NORTH CHARLESTON, SC
- Parts Used:
- 241993101
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Support stude for both vegetable crispers broken off
Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.
None of this was obvious - an online tip from another member was invaluable.
None of this was obvious - an online tip from another member was invaluable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANGELA from MEBANE, NC
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gayle from Hot Springs Village, AR
- Parts Used:
- 240350649
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
When washing the shelf insert glass piece, it broke into a million pieces.
The repair was just as easy as ordering the part which arrived on day three after I ordered it! I had already cleaned up the broken glass insert, so all I had to do was unpack and lay the new shelf in. Took less than a minute!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Greensburg, PA
- Parts Used:
- 5303918344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice tray wouldent fill.
It was simple. I loosened the two screws holding the ice maker unit. Then disconnected the wire harness. Plug in the new ice maker and tighten down the two screws. Held reset button for 15 sec. Done! took ten min. I had a full try of ice the next day!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from FOREST HILL, LA
- Parts Used:
- 240599803
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Meat Pan Cover Broke
Popped out glass, pulled up and the front of cover and pulled froward. Pushed new cover back on to studs and pushed down on cover to lock it to front studs. Put glass on top of new cover. About 3 min total to make repair.
Was this instruction helpful to you?
Thank you for voting!
door wouldn't close by itself anymore and there was black stuff at the bottom of the door
Emptied the shelves off door and pulled door off fridge swet on counter and took out old plug and put new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from DAYTON, OH
- Parts Used:
- 5303918214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
After a power outage my refrigerator went warm & the freezer was cool.
I unplugged the refrigerator and removed the back panel in the freezer. Here the coils were covered in a block of heavy frost. The coils needed to defrost, I allowed this to happen of the course of a few hours. Once this was done I used the wire cutters, cutting the two wires to the thermostat. Doing this I checked the continuity & got no reading. Having ordered the part at a more than reasonable price including 2 day delivery, I was ready to complete the repair. Stripping the thermostat wires connected the the freezer unit, I attached the two wires color to color to the new thermostat. Here I needed to insert both ends into the connector (butt end), crimping both sides. Making sure each end I'd secure. Do this for both sets of wires. Placing the new thermostat back on the the cooper coil (on the same one it was removed from), put the freezer back in place. Here I only screwed in two, in case I need to go back in. I plugged the refrigerator back in turn the settings back to default or factory. Allowed the refrigerator to come back up to temperature for 24-48 hours. I did these and I'm glad to say my 12 year refrigerator is working just like before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from TONEY, AL
- Parts Used:
- 241675704
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
ice maker would not dispense cubes, stuck on crushed ice
turn off ice maker, unplug electoral connection, under bottom of ice maker, remove two screws (hex) under bottom of ice maker, lift up on it to unhook it, take it out. (dump out all ice ). remove back plate on back of ice maker (two screws), the solenoid is held in place with two brass screws, remove them, then remove ground wire from solenoid and two wires, that connect to it,(make a note of how wires go back !). put it all back together and your good to go. . i dont think its really the solenoid that goes out, its the housing that encases it, and you have to buy another solenoid thats encased. good luck
Was this instruction helpful to you?
Thank you for voting!
My water filter cup was cracked and leaked
I ordered a replacement on-line (real simple, visual aids helped more than model nos). Once I received it in the mail, I installed it (no tools required) and now my water filter and ice maker are back to doing what they do best!
Was this instruction helpful to you?
Thank you for voting!
door woulg clunk and drop
took door off(very easy two bolts on top)lift door replace parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Clayton, NC
- Parts Used:
- 241885001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
crusher housing cracked
Removed ice tray, disassembled ice tray assembly and crusher housing making sure to note the spring location, spring etc, installed new plastic housing making sure to reinstall the spring properly and the fixed crusher blade into the notch cutout., reassembled ice tray.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Ellsworth, WI
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker line was freezing
Pulled the unit out from the wall and with a flat head screwdriver and a utility knife I replaced the valve assembly. It was no problem at all.
Was this instruction helpful to you?
Thank you for voting!