25361780012 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The drawer support rail cracked and broke at the end
I unscrewed the old drawer support rail and installed the new one. The phone rep. was excellent. He listened to what I needed, looked up the parts for me, and sent me the correct parts the first time. I think the parts arrived within two days, much faster then I expected. I will be doing business with you again whenever I need parts. Thank you for your excellent service. You exceeded my expectations.
Sincerely,
Rob Ponitz
Sincerely,
Rob Ponitz
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jo Ann from Ruidoso, NM
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broke meat keeper rail
Removed shelf, inverted it, removed broken part (one screw), installed new shelf rail.
Piece of cake.
Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chevy from Jacksonville, FL
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The drawer support rail was broken
I unscrewed the old drawer support and screwed the new one in. It was very simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Standish, ME
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Drawer rail under top shelf broken
It was easy. I handed it to my husband.
Was this instruction helpful to you?
Thank you for voting!
Plastic drawer support had broken from extended use.
This was a truly easy snap-in repair. Because I live in a small fishing village on the coast of Venezuela, the only difficult part was waiting for the part to arrive. I'm very grateful that Part Select makes ordering parts easy and reliable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lancaster, PA
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cheese drawer rail broke
I took out the screw and removed the old rail, then I used the same screw to install the new rail. It took me 2 to 3 minutes. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Megan from Hamden, AL
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Support rail for meat drawer broke
Super easy. We unscrewed the broken rail, and screwed the new rail into place. Much easier than expected!!! We were also pleasantly surprised to have the part arrive the day after we ordered it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from THIBODAUX, LA
- Parts Used:
- 240530701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drwr. suppt. broken-- cracked
took off bad part-- 1 screw-- took every bit of 3 min. to change
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
Both support rails had broken
First, remove shelf unit from refrigerator and lay glass side down on a large flat surface. Observe, then pay attention to assembly. Spent more time with this, drinking coffee, and playing with puppy, than the actual repair. Only had to remove and replace two
phillips head screws. Replace deli - meat drawer after shelf unit is in place in refrigerator. Check for clearance for door to close.
phillips head screws. Replace deli - meat drawer after shelf unit is in place in refrigerator. Check for clearance for door to close.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion from Center Point, IA
- Parts Used:
- 240530601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Left rail was broken
The shelf needed to be removed from refrigerator and then remove the screw and pull the rail from the bracket on the opposite end. After installing the new rail it turned out to be a fraction of an inch too long so I had to file the cracket on the shelf which is metal. The rail slipped back in and was perfect. Easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Hudson, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
not cold enough
per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK from BRADENTON, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Frige and freezer not cooling
I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Spring Hill, FL
- Parts Used:
- 5303918202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Evap coil was solid ice, fridge was 64 degrees.
Exactly as the video showed, except I had to take the evap coil cover off and use a hair dryer to thaw it out. It was still frosting up too much, so I ordered the thermostat as well. Both were really easy, once i saw the location of the defrost timer and the thermostat. Thanks for the great site, prices that put the big store to shame, and the good video too!
Was this instruction helpful to you?
Thank you for voting!