25361768010 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from VENICE, FL
- Parts Used:
- 5303918202
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Refrigerator evaporator coil was icing up
The evaporator coil is behind the freezer. Remove the rack that makes the shelf and remove two 1/4” hex head screws I the back of the freezer to access the coil.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.
I used a hair dryer to melt the ice off the coil.
The thermostat clips on the refrigeration pipe to the coil. Remove the old thermostat and cut the wires at least a few inches from the thermostat. Clip the new thermostat on the pipe and strip about a 1/4” of the wire ends. The electrical connectors (provided with the new part) must be crimped to connect the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EDWIN from ELWOOD, IN
- Parts Used:
- 5308000010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from henrico, VA
- Parts Used:
- 241639502
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
The new motor mount screw holes were not threaded.
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Winlock, WA
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
won't start repaced the run capacitor didn't solve the problem so I ordered a defrost timer
I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- francis from arlington, WA
- Parts Used:
- 241537103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
has lights,no fan or compressor
jump thermostat,fan and compressor came on, ordered thermo from this excllent parts supplier, part came in 4 days later, it was exact replacement, works exactly right!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Spring Hill, FL
- Parts Used:
- 5303918202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Evap coil was solid ice, fridge was 64 degrees.
Exactly as the video showed, except I had to take the evap coil cover off and use a hair dryer to thaw it out. It was still frosting up too much, so I ordered the thermostat as well. Both were really easy, once i saw the location of the defrost timer and the thermostat. Thanks for the great site, prices that put the big store to shame, and the good video too!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Jefferson, MD
- Parts Used:
- 215846604
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Freezer always has ice accumulating
Thermostat assembly, remove light bulb, remove 1 screw, drop thermostat casing, two screws to remove timer from inside and install in reverse. Old Timer had electric motor and lasted 30 years. New one looks to be electronic with plastic motor gears.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laurie from Meridian, ID
- Parts Used:
- 5303918202
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator section warm
My husband watched the video on your website and found it very easy to do the repair. The repair company that diagnosed the problem wanted $210 to do it. The part I ordered was under $20, and after he installed it the refrigerator has been working great. We would highly recommend your site to anyone who needs to fix anything!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Shamokin, PA
- Parts Used:
- 5303918202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
frost build up on freezer coil
purchased a defrost theromast,took about 20-30 minutes to take apart & put back together.delivery was in one day from the time of my purchase.thanks for all ur help &prompt delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK from BRADENTON, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Frige and freezer not cooling
I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Hudson, FL
- Parts Used:
- 5304464438
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
not cold enough
per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Stowe, VT
- Parts Used:
- 5303918202
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Fridge too warm. Top Freezer cold.
I hesitate to say anything since I did exactly what their video told me to do, and it fixed the problem. Couldn't be happier. Was positive I was looking at 1000$ for a new fridge. Love being able to fix it by installing 15$ part myself. Thanks guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ross from Murphy, TX
- Parts Used:
- 5303918202
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Fridge not cold enough
The freezer was still making ice, but the fridge portion was barely cooler than room temp. I came to the website and saw that the defrost thermostat cured this problem over half the time. I was quite dubious because I don't see how that would affect the non-freezer part of the compartment, but since it was a cheap and easy-looking repair, I figured what the heck, lets see if that's it. Sure enough, it's like new again. I still don't understand it, but I'll take it. The repair itself is simple, just cutting out the old switch and splicing in the new. Two wires, and clip it to the copper tubing where the old one was. The switch is accessed easily after taking out four screws in the back of the freezer compartment. The only hard part was removing the ice-maker, and that's just because the two screws that hold it in are a little hard to get a good grip on. Alas, you have to get the ice-maker out to pull out the back panel, so there's nothing for it but to wheedle those screws out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from AuSable Forks, NY
- Parts Used:
- 5303918202
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
warm fridge, cold frosty freezer
remove food, then the shelf, then use a hot air gun to defrost and loosen the back panel, then remove the panel, then defrost the coil and thermostat area. using wire tools, replaced the defrost thermostat,and re-assembled freezwr and test
Was this instruction helpful to you?
Thank you for voting!