25344383407 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bob from Milton, WV
- Parts Used:
- 241885001
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
housing-crusher was broken
removed ice maker box and disassembled crusher unit on front of box and installed new housing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Bryan, TX
- Parts Used:
- 242252702
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Water leaking from back of refrigerator
Followed instructions from others on the blog. Shut off water and electricity to the refrigerator. Removed the cardboard plate. Removed the old water valve. Cut the compression valves off and inserted the tubes into the new water valve. Attached the water valve bracket to the fridge. Tightened copper water supply.Turned on the water - no leaks. Plugged the fridge in. Tried the water and ice in the door. No leaks - everything worked perfectly. THANK YOU PARTS SELECT!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from St louis, MO
- Parts Used:
- 5303918344
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Failed icemaker
First I loosened the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...re-installed the new icemaker first attaching the wires and then fitting over the screw holders and tightened the screws. That was it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Louisville, KY
- Parts Used:
- 242252702
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
water valve failure
removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.
worked fine
worked fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Middletown, CT
- Parts Used:
- 5304469407
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Motor had failed due to ice ejector frozen to tray.
Removed the ice maker. Took off the cover and proceed to remove the motor. The only trick was to dis-assemble the electrical connector to replace the wires. I chose to do this rather than splice the new motor into the existing system and it was simple with a little patience.
Easiest repair to make and half / third the money for a new ice maker. The in-laws have ice again (it was over a year).
Easiest repair to make and half / third the money for a new ice maker. The in-laws have ice again (it was over a year).
Was this instruction helpful to you?
Thank you for voting!
Rust had corroded Front Plate and Drive Blade
Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.
Was this instruction helpful to you?
Thank you for voting!
crisper drawer supports broke
The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DeFuniak Spgs, FL
- Parts Used:
- 5303918344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
ice maker motor shorted out
loosen 2 screws
unplug connector
remove
replug
replace
tighten 2 screws
done
unplug connector
remove
replug
replace
tighten 2 screws
done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Newnan, GA
- Parts Used:
- 240328203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Broken Hinge Bearing
Removed the Plastic Cover at the top of the door. (One Phillips Screw ) Removed the Hex Screws with socket set. Lifted EMPTIED door off bottom hinge. Pulled the broken bearing out with needle nose pliers. (Very Easy!!!) Placed new bearing into slot and reversed the procedure. 15 minutes tops. I spent more time cleaning the door and gaskets than replacing the parts. Funny thing, I called the local appliance parts store and they stated this is a common problem. However, for such a common problem, they didn't carry the part and it would have cost more than what I paid here. Additionally, I paid for 3-5 day delivery. Part was here in 2 days. Awesome!!!! I'll always come here first for all my parts needs. A+++
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paulo from Round Lake, IL
- Parts Used:
- WF2CB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice/water filter needs replacement after 7 months
I just took the old filter off and replaced with the new one, after I run the water for about 15 minutes and tossed the old ice and cleaned the tray.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Concho, AZ
- Parts Used:
- 809069220
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
motor falure of evaporator fan
removed fan unit from frig and installed new motor and then replaced back in frig. No tools needed. need to unplug unit and take apart and put new motor in the unit and then plug back in.
Was this instruction helpful to you?
Thank you for voting!
loud snaping noise when refrig door was opened past 90 degrees and closed again
First I removed one screw holding top hinge trim in place. I than removed two screws holding top hinge from refrig. I removed refrig door and laid it on a table. I than removed two screws holding the door stop and bearing hinge. I replaced the defective parts and reassembled in reverse order. Simple 10 minute repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn D from Rescue, CA
- Parts Used:
- WF2CB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice maker and water were not working.
Ordered new water filter. It arrived, I opened it and took out the old one and put in the new one. I worked perfectly
as soon as I realized I had to remove the protective caps.
as soon as I realized I had to remove the protective caps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from MELBOURNE, KY
- Parts Used:
- WF2CB
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water filter
pushed release button removed filter, installed new filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Alto, NM
- Parts Used:
- 240457701
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
plastic closer plate broken
First removed food from the refrigerator door.
Second removed plastic cover plate and metal plate assembly from top of door.
Third lifted door of metal pin on bottom.
Fourth removed broken closer plate and replaced
with new closer plate.
Set door back in place.
Re secured the metal plate and plastic cover plate.
Replaced the door shelves and food. DONE.
Second removed plastic cover plate and metal plate assembly from top of door.
Third lifted door of metal pin on bottom.
Fourth removed broken closer plate and replaced
with new closer plate.
Set door back in place.
Re secured the metal plate and plastic cover plate.
Replaced the door shelves and food. DONE.
Was this instruction helpful to you?
Thank you for voting!