25360537402 Kenmore Refrigerator - Instructions

All 3 parts were very easy to replace. Thawing out the freezer took the most time. Great videos that go with each part for installation. I will be purchasing again from this company when needed.

Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.

Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

just like the video showed...it was excellent!!!

took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

The instructions given to me by part Select were very good.I replaced the Timer- checked the heater with oham meter it was good- checked the door weather striping it was good and replaced the thermostat with new .So at this point I may need to call a professional unless some one has another solution.

I hesitate to say anything since I did exactly what their video told me to do, and it fixed the problem. Couldn't be happier. Was positive I was looking at 1000$ for a new fridge. Love being able to fix it by installing 15$ part myself. Thanks guys.

First of all I am 78YO, retired. Handy but NOT a handyman. There were two parts to replace. The Defrost Timer was very very easy and went just like the video. 20 minutes at the most. No surprises with only the most basic tools. The Defrost Thermostat was a little trickier. Took about 1 1/2 hours. The Thermostat disconnect plug was not like the video and was stuck hard. Had to use two needle nose pliers to finally get it apart. The rest went OK. The shrink seals were way too large for the job and my Hair Dryer was not able to shrink them enough for a good seal. Used a much smaller shrink seal that a friend had and it worked great. Suggest they use a smaller shrink that works with a hair dryer instead off the blow gun in the video. Wrapped the connection with electrical tape as others have suggested in addition to the Shrink Seal. Went together easy and am very very happy camper. Saved $295 from the Sears Repair Estimate. Dave

Removed the lower trim panel from front of fridg. and loosened two screws enough to turn it about 1/4 inch so the screw heads were in the larger holes. Pulled it out disconnected the wire connector and transfered the heat shield and screws to the new clock, connected the wire connector and aligned the screws. tightened them and job done. Has worked like new sense. Thanks Roger

I first thought the defroster heater broke - took the back wall of the freezer off and cooling fins were fine. Then took the defroster timer out and opened it up. The contacts were badly burnt so the compressor and fan ran during only part of the cooling cycle. Replacing the timer took less than 5 minutes - turn off the power, remove one screw to take out the control box, cut the ground wire (new timer housing is plastic and does not have a ground connection), remove two screws to unmount the timer, unplug the old timer, plug in the new timer, fasten with two screws, put the control unit in and fasten with one screw, turn power back on.

Unplug the refrigerator. Removed the right hand top shelf. Used a 1/4" nutdriver to remove rear center mounting screw for Control Housing. Used Phillips screwdriver to remove two mounting screws for timer. Unplug cable from timer and plug it into the new timer. Install the new timer and re-install the Control Housing. Plug in the refrigerator and adjust the timer to start the unit. This was a snap with the diagnostic provided by Part Select. At first I thought it was the fan rubbing but when I removed the cover (two screws) it was obvious that wasn't the problem. The diagnostic hinted that it was either the timer or the motor capacitor making the noise. Because the noise continued after turning OFF the control, I thought it was the timer...I was right.

Ordered the new part-Unplugged the refrigerator - took off the cover over the defective timer - put in the new part put the cover back on - plugged the refrigerator back in - so far, so good!~

I watched the video you had on-line and it was simple. Thank you so much

I watched the step-by-step installation video and followed the instructions therein.