59665264701 Kenmore Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stacy from FREDERICK, MD
- Parts Used:
- WP67005140
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door handle cracked in half .
Use a screw driver and it was easy to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Conley from richmond, TX
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker failure to produce ice
The repair was simple.
I first did a diagnosis of the optical cuircuits and found them good. The tray heated up and when resetting the moor controller, the water cyccled to fill the tray so the only other thing it could be was the motor controller.
removed the service door for the ice maker
I removed the wire protectore screw and shroud
pulled the icemaker unit out and unplugged the unit
removed the motor controller end cap
unscrewed 3 screws holding the motor controller
removed and replaced the motor controller. ensured that all wire harness connector poiints were solid
reverse the above instructions and in 5 hours I was getting ice again!
$90 turned out to be a savings from the $250 it would have cost to have someone come out and look at the fridge.
I highly recommend to anyone who can read and use a screwdriver to perform this repair if you have diagnosed this as the root of your problem!
I first did a diagnosis of the optical cuircuits and found them good. The tray heated up and when resetting the moor controller, the water cyccled to fill the tray so the only other thing it could be was the motor controller.
removed the service door for the ice maker
I removed the wire protectore screw and shroud
pulled the icemaker unit out and unplugged the unit
removed the motor controller end cap
unscrewed 3 screws holding the motor controller
removed and replaced the motor controller. ensured that all wire harness connector poiints were solid
reverse the above instructions and in 5 hours I was getting ice again!
$90 turned out to be a savings from the $250 it would have cost to have someone come out and look at the fridge.
I highly recommend to anyone who can read and use a screwdriver to perform this repair if you have diagnosed this as the root of your problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from DURYEA, PA
- Parts Used:
- WP67001314
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drawer was cracked and fell apart
Ordered replacement drawer and inserted into the drawer holder
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMIE from HANOVER, PA
- Parts Used:
- W10190935
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
icemaker wasn't making ice
i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we get many more years out of this icemaker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Fairview Heights, IL
- Parts Used:
- 8201515
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker wouldn't cycle
Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- R from Princeton, WI
- Parts Used:
- 67005125
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken freezer door handle
I ordered the part at 1:30pm and I received it at 1pm the very next day. The price was good ($10)and the shipping cost was reasonable ($7). I would recommend PartSelect to anyone!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from Lancster, CA
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker stopped making ice
Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johanne from Vista, CA
- Parts Used:
- WP67005140
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken handle
SUPER EASY!! UNCREW, AND SCREW ON NEW PART. PERFECT PART, COLOR, SERVICE. THANK YOU !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sally from WAKEFIELD, RI
- Parts Used:
- WP67005141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken freezer door handle
unscrewed the broken one, screwed the new one on. SIMPLE SIMPLE took 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- julio from pembroke pines, FL
- Parts Used:
- WPM0274057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
fz door loss a shim and door was resting on top of refrigirator door
Remove 3 screws, took top hinge out, fz door and inserted shim...done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Boca Raton, FL
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My ice maker just stopped working
I Removed 3 screws, pulled off the plate and put the new one on, screwed in 3 screws and away I went. I could not believe how easy it was to order the part and how quickly it arrived. I was very pleased. And I was literally screaming with excitement when I heard the first set of ice cubes drop!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from WEST CHESTER, PA
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No ice
I removed the icemaker. One screw at the bottom and then unplug the electric. Remove the old motor from the face that has 3 screws holding it. Put the new motor in. A very simple job. I now have a full ice bin by the next morning.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from BASKING RIDGE, NJ
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker clicked CW and CCW, but did not make ice
Replaced the control of the ice maker assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Hornsby, TN
- Parts Used:
- 8201515
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
ice maker quit working
I was amazed when Fed Ex pulled up to our front door the following day after I ordered the parts, I was wondering what they were delivering and to my amazement it was the parts I had ordered from parts select the previous day , thank you so much , you are awesome. My 73 year old husband who is a 5 year cancer survivor had the part installed and we were ready to start making ice within 1 hour.He went by the installation information sent in by your customers. Thank you all, Jo Mesplay
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MARYLAND HTS, MO
- Parts Used:
- WPW10662129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
freezer (later fridge too) wouldn't stay cold~
****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years
Was this instruction helpful to you?
Thank you for voting!